background image

Straight Line Ripping

Refer to Figure 10
The miter bar MUST be removed when straight line ripping.

1.  Remove the miter bar from the jig base. The table saw's 

fence is used to set the cutting width and guide the cut.

2.  Loosen the five star knobs on each end of the adjustable 

fence and position it parallel to the jig's long edges. Tighten 

the knobs. If needed, retract the adjustable stop. 

3.  Place the workpiece against the jig. Position the hold down 

clamps along the workpiece. Make sure they will not come 

in contact with the saw blade, guard or riving knife during 

the cut. Tighten the five star knobs to secure the workpiece. 

DO NOT try to cut pieces that are too narrow to be secured 

by the hold down clamps.

4.  Position the long side of the jig tight against the table saw's 

fence and make the cut. Keep the jig tight against the fence 

as the workpiece is fed into the blade.

Figure 10

Table Saw's 

Fence

OPERATION

6

GENERAL MAINTENANCE

     WARNING

When servicing, use only identical replacement parts. Use of 
any other parts may create a hazard or cause product damage. 
To ensure safety and reliability, all repairs should be performed 
by a qualified service technician.

MAINTENANCE

6

MAINTENANCE

6

     WARNING

 

Keep the jig dry, clean, and free from oil and grease. Always 
use a clean cloth when cleaning. Never use brake fluids, 
gasoline, petroleum based products or any strong solvent 
to clean the jig. Chemicals can damage, weaken or destroy 
plastic which may result in serious personal injury.

Содержание 71395













Отзывы: