background image

 

 

INTRODUCTION 

Thank You for Purchasing a PowerSmart

®

 Product. This manual provides information regarding the safe 

operation and maintenance of this product. Every effort has been made to ensure the accuracy of the 
information in this manual. PowerSmart

®

 reserves the right to change this product and specifications at 

any time without prior notice. 

Please keep this manual available to all users during the entire life of the generator. 

This manual contains special messages to bring attention to potential safety concerns, 
generator damage as well as helpful operating and servicing information. Please read all the 
information carefully to avoid injury and machine damage. 

QUESTIONS? PROBLEMS? 

In order to answer questions and solve problems in the most efficient and speedy manner, contact 
Customer Service at (800) 791-9458, Mon-Fri 9am-5pm EST or email: [email protected]

NOTICE REGARDING EMISSIONS 

Engines that are certified to comply with U.S. EPA emission regulations for SORE (Small Off Road 
Equipment), are certified to operate on regular unleaded gasoline, and may include the following 
emission control systems: (EM) Engine Modifications and (TWC) Three-Way Catalyst (if so equipped). 

 

SAFETY INFORMATION 

 

This symbol points out important safety instructions which, if not followed, could endanger 
the personal safety and or property of yourself and others. Read and follow all instructions in 
this manual before attempting to operate this machine. Failure to comply with these 
instructions may result in personal injury. 
 

WARNING!

 This machine was built to be operated according to the safe operation practices 

in this manual. As with any type of power equipment, carelessness or error on the part of the 
operator can result in serious injury. This machine is capable of amputating fingers, hands, 

toes and feet and throwing foreign objects. Failure to observe the following safety instructions could 
result in serious injury or death. 
 
It is your responsibility to restrict the use of this power machine to persons who read, understand 
and follow the warnings and instructions in this manual and on the machine. 

 
ROTATING PARTS! Only use clean-out tool to clear blockages. NEVER use your 
hands. 
 
 
 
NEVER direct discharge towards persons or property that may be injured or damaged 

by thrown objects. 
 
 
 
Keep people away from unit while operating. Keep children out of work area and under 

watchful care of a responsible adult. 
 
 

 

 

 

Содержание DB7124

































Отзывы: