background image

5

• To avoid accidental start-ups, remain in the starting position when turning the snow thrower on. The
operator and the snow thrower must be in a stable position during start-up. See the section titled
Starting/Stopping Instructions.
• Use this snow thrower only for the purposes it was designed.
• Do not overreach. Always keep proper footing and balance.
• Hold the snow thrower with both hands while it is in use. Keep a firm grip on the handles.
• If the impeller does not rotate freely due to ice, thaw the snow thrower thoroughly before attempting to
use it.
• Do not attempt to clear the impeller while the motor is running.
• Keep clothing and body parts away from the impeller.
• Stop the motor when stopped or when moving from one location to another.
• Remove the battery pack when it is being transported and when it is not in use.
• After striking a foreign object, turn the snow thrower off and remove the battery pack, and then inspect
it for damage. Repair any damage before restarting and using the snow thrower.
• If the snow thrower starts to vibrate abnormally, stop the snow thrower immediately and attempt to
determine the cause. Vibration is generally an indication of danger.
• Stop the motor and remove the battery pack whenever the operator is not in the operating position,
before unclogging the impeller, and before making any repairs, adjustments, or inspections.
• Do not discharge snow onto public roads or near moving traffic.
• Allow the snow thrower to run for a few minutes after clearing snow in order to prevent moving parts
from freezing.
• Only use identical replacement parts and accessories for this snow thrower. The use of nonidentical
parts or accessories could lead to serious injury to the user or damage the snow thrower, and will void the
warranty.
• Do not pick up the snow thrower while it is running. The snow thrower is designed to travel along the
ground.
• Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts.
• Wear rubber boots when operating the snow thrower.
• Operation of the snow thrower in the hand-held position is unsafe, except in accordance with the special
instructions for such use provided in the operator’s manual.
• Store Idle Snow Throwers Indoors – When not in use, snow throwers should be stored indoors in dry,
locked-up place – out of reach of children.

GENERAL SAFETY RULES

• Verify that the snow thrower is secure while transporting.
• Store the snow thrower in a dry area that will prevent unauthorized use or damage. Keep out of the
reach of children.
• Keep handles dry, clean, and free of debris. Clean the snow thrower after each use. Refer to the
Maintenance Section in this manual for more information.
• If the labels on the snow thrower become defaced or start to lift off, contact the toll-free helpline, at (8

00)

791-9458

.

• Keep these instructions in a safe place for future reference. Refer to them often, and use them to instruct
other users. Anyone who uses this snow thrower must read these instructions carefully.
• Maintain the snow thrower with care. Follow the instructions for lubricating and changing

C AUTION

USE ONLY

PowerSmart

®

APPROVED REPLACEMENT BATTERIES, OTHER BATTERIES

MAY CAUSE INJURY OR DAMAGE TO THE SNOW THROWER. USE ONLY WITH

PowerSmart

®

40V BATTERIES and CHARGER .

Содержание DB2418




















Отзывы: