background image

 

POWX093 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

4

 

www.varo.com 

4  SYMBOLS 

In this manual and/or on the machine the following symbols are used: 

 

Denotes risk of personal injury 
or damage to the tool. 

 

Wear ear guards and goggles 

 

Read manual before use 

 

Wear a mask In dusty conditions 

 

In accordance with essential 
requirements of the European 
directive(s) 

 

"Class II - The machine is 
double insulated; Earthing wire 
is therefore not necessary 

5  GENERAL POWER TOOL SAFETY WARNINGS 

Read  all  safety  warnings  and  all  instructions.  Failure  to  follow  all  warnings  and  instructions 
may  result  in  electric  shock,  fire  and/or  serious  injury.  Save  all  warnings  and  instructions  for 
future reference. The term "power tool" in the warnings refers to your mains operated (corded) 
power tool or battery operated (cordless) power tool. 

5.1 

Work area 

 

Keep work area clean and well lit. Cluttered and dark areas invite accidents. 

 

Do not operate power tools in explosive atmospheres, such as in the presence of 
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or 
fumes. 

 

Keep children and bystanders away while operating a power tool. Distractions can cause 
you to lose control.  

5.2 

Electrical safety 

Always  check  that  the  power  supply  corresponds  to  the  voltage  on  the 
rating plate. 

 

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any 
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching 
outlets will reduce risk of electric shock. 

 

Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges 
and refrigerators. There is an increased risk of electric shock if your body is earthed or 
grounded. 

 

Do not expose power tools to rain or wet conditions. Water entering a power tool will 
increase the risk of electric shock. 

 

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power 
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled 
cords increase the risk of electric shock. 

 

When operating a power tool outdoors, use an extension cord suitable for outdoor use. 
Use of a cord suitable for outdoor use reduces the risk of electric shock. 

 

If operating a power tool in a damp location is unavoidable, use a residual current device 
(RCD) protected supply. Use of an RCD reduces the risk of electric shock. 

Содержание POWX093














Отзывы: