POWX07587
EN
Copyright © 2017 VARO NV
P a g e
|
14
www.varo.com
CAUTION:
▪
The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.
Return the lower blade guard (7) to its original position. Lower the handle to make sure
that the lower blade guards move properly. Make sure shaft lock has released spindle
before making cut.
9.3
Adjusting riving knife (fig 23,24 & 25)
There must be a clearance of about 5
– 6 mm between the riving knife and the blade teeth
when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first
loosening clamping nut (37) by hand counterclockwise and then loosening hex bolt (3)
counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,
securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that
the riving knife is secured and that the top blade guard works smoothly before cutting.
The riving knife has been installed before shipment from the factory so that the blade and
riving knife are in a straight line after your simple set-up. Refer to the section titled
“Repositioning riving knife” for the set-up.
CAUTION:
▪
If the blade and riving knife are not aligned properly, a dangerous pinching condition may
result during operation. Make sure the riving knife is positioned between both outer ends
of the blade teeth when viewing from the top. You could suffer serious personal injury
while using the tool without a properly aligned riving knife. If they are not aligned for any
reasons, always have an authorized service center repair it.
▪
When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt
only after loosening the clamping nut.
9.4
Installing and adjusting rip fence (43)(Fig. 26)
▪
Install the rip fence on the table so that the rip fence holder engages with the guide rail.
Tighten the clamping screw (42) of the rip fence firmly clockwise.
▪
Loosen the clamping screw (41)
▪
Slide the rip fence and secure it so that the far end from you of the rip fence is aligned with
the point at which the front edge of saw blade just appears from top surface of the
workpiece. The purpose of this adjustment is to reduce risk of kick-back toward operator
that cut piece from the workpiece is pinched between the saw blade and rip fence and
finally pushed out toward operator. The line A varies by thickness of workpiece or the table
level. Adjust the position of the rip fence according to the thickness of the workpiece. After
adjusting the rip fence, tighten the clamping screw (41) firmly. (Fig. 27)
NOTE:
▪
There are four patterns to position the rip fence as shown in the figure. Rip fence has two
slits on its sides, one slit with an elevated fringe nearby on the same side and the other
without it. Use the surface of rip fence with this fringe facing the workpiece only when
cutting off into a piece of a thin workpiece.
▪
To change the rip fence pattern, remove the rip fence from the rip fence holder by
loosening the clamping screw (41) and change the facing of the rip fence to the rip fence
holder so that the rip fence faces the rip fence holder according to your work as shown in
the figure. (Fig. 28)
▪
Insert the square nut on the rip fence holder into the back end of either slit of the rip fence
so that they fit as shown in the figure.
▪
To change from the pattern A or B to the pattern C or D, or in adverse case, remove the
square nut and clamping screw (41) from the rip fence holder, then position the clamping
screw (41) and square nut on the opposite position of the rip fence holder compared to the
original position. Tighten the clamping screw (41) securely after inserting the square nut of
the rip fence holder into the rip fence slit.
Insert the square nut on the rip fence holder into the back end of either slit of the rip fence so
that they fit as shown in the figures. (Fig. 28 & 29)
