background image

Warranty & Service

The WMH Tool Group warrants every product it sells.  If one of our tools needs service or repair, one of our
Authorized Repair Stations located throughout the United States can give you quick service.

In most cases, any one of these WMH Tool Group Repair Stations can authorize warranty repair, assist you in
obtaining parts, or perform routine maintenance and major repair on your JET, Powermatic, Performax, or
Wilton tools.

For the name of an Authorized Repair Station in your area, please call 1-800-274-6848.

More Information

Remember, the WMH Tool Group is consistently adding new products to the line.  For complete, up-to-date
product information, check with your local WMH Tool Group distributor.

WMH Tool Group Warranty

The WMH Tool Group makes every effort to assure that its products meet high quality and durability standards
and warrants to the original retail consumer/purchaser of our products that each product be free from defects in
materials and workmanship as follow:  1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECI-
FIED OTHERWISE.  This Warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence or accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of mainte-
nance.

THE WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, FROM
THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY IMPLIED
WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU. THE WMH TOOL GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES
TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL
DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLU-
SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.

To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to an
Authorized Repair Station designated by our office.  Proof of purchase date and an explanation of the complaint
must accompany the merchandise.  If our inspection discloses a defect, we will either repair or replace the
product, or refund the purchase price if we cannot readily and quickly provide a repair or replacement, if you are
willing to accept a refund.  We will return repaired product or replacement at WMH's expense, but if it is
determined there is no defect, or that the defect resulted from causes not within the scope of WMH's warranty,
then the user must bear the cost of storing and returning the product.  This warranty gives you specific legal
rights; you may also have other rights which vary from state to state.

The WMH Tool Group sells through distributors only.  Members of the WMH Tool Group reserve the right to
effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they
may deem necessary for any reason whatsoever.

This manual has been prepared for the owner and operators of a Powermatic Model 6108 Edge
Sander.  Its purpose, aside from machine operation, is to promote safety through the use of
accepted correct operating and maintenance procedures.  Completely read the safety and main-
tenance instructions before operating or servicing the machine.  To obtain maximum life and
efficiency from your sander, and to aid in using the machine safely, read this manual thoroughly
and follow all instructions carefully.

Содержание 6108





















Отзывы: