Powermate PFTT142.1 Скачать руководство пользователя страница 19

Страница: 19 / 20

ENG - 19

Questions? Call Toll Free at 1-800-737-2112

PROBLEM

POSSIBLE CAUSE(S)

SOLUTION(S)

Engine difficult to start

1 . Out of fuel

2 . Engine Switch Off

3 . Engine is not primed

4 . Spark plug wire disconnected

5 . Fouled spark plug

6 . Dirty Carburetor

7 . Clogged air filter

8 . Contaminated Fuel

1 . Add fresh fuel

2 . Turn engine switch on

3 . Push primer 3 times .

4 . Attach spark plug wire to spark plug

5 . Remove spark plug . Inspect . Replace if

necessary

6 . Take unit to an authorized service center

for Carburetor cleaning

7 . Remove and clean air filter

8 . Drain fuel tank . Clean fuel tank . Fill with

fresh fuel

Engine Problems

Engine smokes excessively

Engine runs very “rough”

Engine runs erratically

Engine cannot maintain full speed

1 . No Engine Oil

2 . Engine oil not at proper level

3 . Fouled spark plug

4 . Clogged air filter

5 . Contaminated Fuel

6 . Carburetor out of adjustment

1 . Add engine oil

2 . Check engine oil . Add or drain engine oil if

necessary

3 . Remove spark plug . Inspect . Replace if

necessary

4 . Remove and clean air filter

5 . Drain fuel tank . Clean fuel tank . Fill with

fresh fuel

6 . Take unit to an authorized service center

for Carburetor adjustment

Excessive vibration / noise

1 . Loose parts

2 . Engine problems (above)

1 . Tighten all fasteners

2 . Refer to engine solutions (above)

Tines will not rotate

1 . Debris interfering with tines

2 . Tines loose

3 . Damaged drive belts

1 . Remove debris from around tines

2 . Replace tine bolts and nuts

3 . Replace drive belts

Tines continue to rotate when

lever is not engaged

1 . Damaged drive belts

1 . Replace drive belts

Engine will not stop

Faulty switch

Replace switch

Tines will not cut properly

1 . Damaged or worn tines

2 . Tines assembled incorrectly

1 . Replace tines

2 . Refer to “Install the Tines” Section

Frequent engine stalling

1 . Excessive tilling speed / depth

2 . Engine problems (above)

1 . Till at a moderate pace . Make multiple

passes .

2 . Refer to engine solutions (above)

Troubleshooting

• Save all instructions

Содержание PFTT142.1





















Результаты поиска

Содержание PFTT142.1

Отзывы:

Бренды по названию

Популярные бренды

Powermate PFTT142.1, Руководство оператора

Результаты поиска

Содержание PFTT142.1

Отзывы:

Бренды по названию

Популярные бренды