Powermate PFTT142.1 Скачать руководство пользователя страница 12

Страница: 12 / 20

ENG - 12

Questions? Call Toll Free at 1-800-737-2112

Operation

• Save all instructions

Pre-Start Inspection

1 . Make sure all safety guards are in place and all nuts and

bolts are secure .

2 . Check oil level in engine crankcase . See your engine

manual for procedure and specifications.

3 . Inspect air cleaner for cleanliness . See your engine

manual for procedure .

4 . Check the fuel supply . Fill the fuel tank no closer than 1

inch from top of tank to provide space for expansion .

Use fresh unleaded gasoline with an octane rating of 87

or higher . Do not use gasoline containing more than 10%

ethanol . Use of non-ethanol fuel is best . We recommend

the continuous use of a fuel additive /stabilizer to

counteract the effects of ethanol . These additives also

prolong the shelf life of gasoline . See your engine

manual for additional fuel recommendations .

5 . Be sure spark plug wire is attached and spark plug is

tightened securely .

6 . Examine underneath and around engine for signs of oil

or fuel leaks .

7 . Inspect fuel hoses for tightness and fuel seepage .

8 . Look for signs of engine damage .

9. Remove excessive debris from muffler area and

recoil starter .

10 . Remove any debris from tines and tine shafts .

11 . Move the tiller to the area of operation .

12 . Check position of wheels swing plate should be in the

tilling mode position .

13 . Check drag bar position .

Start the Engine

1 . Press ON/OFF switch to ON position . (See Figure 12)

2 . Push primer bulb 3 times . Wait 2 seconds between

each push .

3 . Place left hand on upper handle . (See Figure 13)

4 . Grasp starter handle and pull out slowly, until you feel

tension in the starter rope . (See Figure 13)

5 . Pull rope with a rapid full arm stroke until engine starts .

6 . Do not allow the starter rope to snap back . Let the

starter rope slowly rewind .

IMPORTANT: Engine is shipped from factory without oil. You

must add engine oil before starting engine.

CAUTION

Please do not start your tiller until you have read the

manual that came with your engine, and the sections in

this manual title controls, adjustments and safety . If you

have read these, follow the steps below to start your tiller .

Always perform this pre-start checklist before starting the

engine .

WARNING

Gasoline is highly flammable and must be handled with

care. Never fill the tank when the engine is hot or running.

Always move outdoors to fill tank.

WARNING

Always keep hands and feet clear of rotating machine

parts .

Figure 12

Figure 13

Содержание PFTT142.1





















Результаты поиска

Содержание PFTT142.1

Отзывы:

Бренды по названию

Популярные бренды

Powermate PFTT142.1, Руководство оператора

Результаты поиска

Содержание PFTT142.1

Отзывы:

Бренды по названию

Популярные бренды