PowerMaster rsw Скачать руководство пользователя

Страница: 24 / 28

5. Run the operator to the OPEN limit and repeat

Step #3

for the outside horizontal edge.

6. Test the

OPEN OBSTRUCTION SENSING SYSTEM

by depressing the inside horizontal

edge sensor while the gate is opening.

NOTE: The operator should repeat the STOP AND REVERSE procedure.

NOTE: If an edge is activated twice, or a second edge is activated before a limit is hit

(full open or close), operator will stop and sound a warning horn. To reactivate system,

turn operator power switch OFF then ON.

NON-CONTACT SENSOR INSTALLATION

1. Install photoelectric cell as

close to FULL OPEN and FULL

CLOSED position of gate as

possible.

2. Photocells should be installed

across the gate opening and

behind the gate at least 10

inches above ground (see

image on right).

NOTE: A separate pedestrian

gate must be installed if there

is no other entry access but

the vehicular gate.

Photo Electric Cell

(For Close Direction)

Photo Electric Cell

(For Open Direction)

NON CONTACT SENSOR CONNECTION

10 11 12 13 14

Open Photocell

Sensor

Close Photocell

Sensor

3. Connect NON-CONTACT sensors to the control board as shown in Figure 16.

NOTE: Close photocell is connected to Terminal #11 and Terminal #14. Open

photocell is connected to Terminal #10 and Terminal #14.

FIGURE 16

Содержание rsw





























Результаты поиска

Содержание rsw

Отзывы:

Похожие инструкции для rsw

Бренды по названию

Популярные бренды

PowerMaster rsw, Инструкция по установке и эксплуатации

Результаты поиска

Содержание rsw

Отзывы:

Похожие инструкции для rsw

Бренды по названию

Популярные бренды