manualshive.com logo in svg

PowerLift SBL460, Руководство пользователя

Поделиться
Скачать
PowerLift SBL460 Скачать руководство пользователя страница 18

S T E P

6

Be careful to assemble all components
in the sequence they are presented.

A.

Open hardware package labeled “Step 6”.

B.

See Note 1. Insert front pivot shaft (AE) into vertical mainframe (E) as show using:

one 41 (square head bolt 10mm x 55mm with dog point) *
one 53 (standard nut 10mm)

* Note: Be sure that (41) bolt goes into the hole in the center of the front pivot shaft (AE) and wrench 

tighten (41) bolt first and then wrench tighten (53) nut last. It may be necessary to “feel” for the hole 
in the center of the shaft by sliding a very small diameter allen wrench all the way thru first to help 
you line up the parts.

C.

Slide left lat beam (AF) on to the front pivot shaft (AE). See Note 2. Install pillow block bearing (22) on
to left lat beam (AF) as shown using:

two 38 (round allen head 10mm x 30mm full thread bolt)
two 55 (spring lock washer 10mm)

D.

Slide right lat beam (AG) on to the front pivot shaft (AE). See Note 2. Install the other pillow block bearing (22) 
on to the right lat beam (AG) as shown using:

two 38 (round allen head 10mm x 30mm full thread bolt)
two 55 (spring lock washer 10mm)

E.

Secure left and right lat beams together (finger tighten only) by using:

two 36 (hex bolt 10mm x 75mm partial thread)
four 51 (flat washer 10mm)
two 54 (nylon lock nut 10mm)

F.

Center the chrome lat adjustment bar (AH) between the left lat beam and right lat beam.  Slide the rear
pivot shaft (AE) thru the right lat beam (AG) and then thru the chrome lat adjustment bar (AH), and then
thru the left lat beam (AF).

G.

Install bolt (41) (square head bolt 10mm x 55mm with dog point) and nut (53) (standard nut 10mm) into the 
threaded hole on the back side of the chrome lat adjustment bar (AH) as shown. *

* Note: Be sure that (63) bolt goes into the hole in the center of the rear pivot shaft (AE) and wrench 

tighten (63) bolt first and then wrench tighten (53) nut last. It may be necessary to “feel” for the hole
in the center of the shaft by sliding a very small diameter allen wrench all the way thru first to help 
you line up the parts.

H.

See Note 2. Install both pillow block bearings (22) onto each side of the rear pivot shaft (AE) as shown using:

four 37 (hex bolt 10mm x 85mm partial thread)
four 55 (spring lock washer 10mm)
four 56 (flat washer 10mm)
four 54 (nylon lock nut 10mm)

I.

Install both lat handles (AJ) into left and right lat beams as shown using:

two 3 (black lat end cap 2.75” x 0.375”)
two 55 (spring lock washer 10mm)
two 40 (round allen head 10mm x 20mm full thread bolt)

Note: At this point you should close the gap between the left and right lat beams at their connection 
point. Use a rubber mallet to knock the two parts together tightly.

You should now wrench tighten all bolts in this step.

J.

Install two plastic bolt end covers (26) over bolts (36).

17

mm

Inch

Note:

You will need assistance in doing this step to properly align all parts. 
Do not wrench tighten until instructed to do so.

Содержание SBL460



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды