manualshive.com logo in svg

PowerLift SBL460, Руководство пользователя

Поделиться
Скачать
PowerLift SBL460 Скачать руководство пользователя страница 12

S T E P

3

Be careful to assemble all components
in the sequence they are presented.

A.

Open hardware package labeled “Step 3”.

B.

Install seat pad frame (M) into lat support frame (J). See Note 1. Install 2 1/2” pivot shaft (N) to connect the
seat pad frame and the lat support frame. Secure as shown by using:

two 40 (round allen head10mm x 20mm full thread bolt)
two 55 (spring lock washer 10mm)
two 51 (flat washer 10mm x 30mm)

C.

Attach seat adjustor (P) to the flanges beneath the seat pad frame (M) using:

one 33 (hex bolt 12mm x 95mm partial thread)
two 50 (flat washer 12mm)
one 48 (nylon lock nut 12mm)

D.

Attach hold down brackets (R) and (S) to lat support frame (J).

Note: hold down brackets should be angled UP (not down). 

Install using:

two 35 (hex bolt 10mm x 100mm partial thread)
four 56 (flat washer 10mm)
two 54 (nylon lock nut 10mm)

E.

There is a threaded end at the bottom of shock cylinder (U). Screw the threaded end of the shock
cylinder (U) into the post protruding from the lat base frame (D) as shown. Tighten by hand until snug.

F.

Install preacher support (V) over the shock cylinder (U) and secure it to lat base frame (D) as shown using:

two 32 (hex bolt 12mm x 105mm partial thread)
four 50 (flat washer 12mm)
two 48 (nylon lock nut 12mm)

G.

Insert foot hold down bar (W) thru the base of the preacher support (V) and hold in place by installing 
both rubber foot covers (12) as shown.

H.

Install back pad (T) on to lat support frame (J).  Tighten pad bolts to a snug fit.  Do not over-tighten any pad 
bolts.  Over - tightening pad bolts will cause T - nuts in pads to strip out.  Install using:

three 42 (hex bolt 8mm x 70mm full thread)
three 60 (spring lock washer 8mm)
three 61 (flat washer 8mm)

I.

Install seat pad (Q) on to seat pad frame (M).  Tighten pad bolts to a snug fit.  Do not over - tighten any pad 
bolts.  Over - tightening pad bolts will cause T - nuts in pad to strip out.  Install using:

two 45 (round allen head 8mm x 20mm full thread bolt)
two 60 (spring lock washer 8mm)
two 61 (flat washer 8mm)

J.

Slide both foam rollers (10) on to hold down brackets (R) and (S).  Secure each foam roller in place by 
inserting a round plastic end cap (17).

Note: At this point you should wrench tighten all hardware in Step 3 except the seat pad and
back pad bolts. Never wrench tighten any pad bolts.

11

mm

Inch

Содержание SBL460



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды