background image

INSTALLING THE LOG SPLITTER

Installing the Wheels and Supporting Feet

1. Carefully unpack the Main Body of the Log 

Splitter from the box and, with the help of another 

person, place it on the foam material included 

with the box. (See Figure 2)

2.  Place  the  supporting  feet  (C  in  Figure  2)  and 

attach  to  the  Main  Body  (B  in  Figure  2).  Attach 

using 2 screws (21) and 2 nuts (20) then tighten. 

(See Figure 3)

3. While the Main Body is still supported on the 

foam  block,  attach  safety  rings  (59)  and  the  2 

wheels (60) to the shaft of the wheel frame (61), 

then use the wheel shaft cover (58) to cover the 

wheels.

4. Make sure that the wheels are able to turn free-

ly and uniformly. (See Figure 3).

Installing the Operating Handle

Unpack  the  operating  handles  (54/55)  from  the 

box and screw them in the receiving hole (52) of 

the handles on the Main Body, then turn the han-

dles to tighten. (See Figure 4).

The Log Splitter is now assembled and ready for 

use.

6

OPERATING PROCEDURE

1. 

Prepare Work Area

 

– Make it safe and efficient by planning the work before you begin. 

Position your logs for splitting within easy access. Prepare an area where you will place 

the split logs also within easy reach. If they will be loaded into a receptacle or on a truck, 

position as near as possible. 

2. 

Prepare Logs for Splitting

 – Sort out your logs before you start splitting. Separate logs 

you can split from the logs you cannot, logs that are too long, too small, and too green. 

Check out Operating Safety Rules for more details. Remove any foreign material that may 

obstruct the Log Splitter operation such as nails, wires, or screws. These may also get 

flung during splitting and cause an accident. Remove any branches from the log as well. 

3. 

Setup Power Source

 – Locate a power outlet that meets the required power require-

ments. Connect the Log Splitters power cord to the power outlet and make sure it is se-

cure. If the Log Splitter is too far for the power cord to reach the power outlet, use a power 

extension cord that meets the required power load to connect the Log Splitter to the power 

Содержание XM-580

















Отзывы: