Powerbox Australia Pty Ltd
Powerbox Pacific Ltd
4 Beaumont Rd Mount Kuring Gai NSW 2080 AUSTRALIA
1800 251 380 [email protected]
www.powerbox.com.au
1a Henry Rose Place Albany Auckland 0632 NEW ZEALAND
09 4158 320 [email protected]
www.powerbox.co.nz
Sydney
(Head Office)
Auckland
(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death)
Version 1.0 10/2018
2
AC-Input
85...265Vac , 47...63Hz , 110…375Vdc
Input Rating
100...240Vac , 115Vac <0.8A 230Vac <0.3A
Rated DC-Voltage
5V
9V
12V
15V
24V
48V
60V
Rated DC-Current
5A
3.3A
2.5A
2A
1.3A
0.6A
0.5A
Ripple 20MHz 230Vac
15mV
15mV
10mV
10mV
50mV
100mV
100mV
DC adj. range
4,9-5,25V
8,5-9,9V
11,4-13,6V
14,2-22,5V
23,5-28,5V
45,6-53V
57-66V
Order Code
OSW00301.(volt) example: OSW00301.12
Factory Adjust. Tolerance Uout ± 1%
Load regulation
< ± 0.5% 10-100%, 100-10%
Switching Frequency
70KHz typical
Basic Load
0 A
Efficiency
Up to 86%
Load Protection
1,2x I
rated
,auto recovery
Voltage Protection
140% of U
out
, auto recovery
Short Circuit Protection
Continuous
Temperature Control
Not available
Hold Up Time
> 40ms 230Vac with full load
Inrush Current
< 17A (230Vac)
Terminal Connects:
1 = L
SK1
2 = N
1 = Sense - (
5V only)
Sk2
2 = DC -
3 = DC +
Screw terminal order
codes for SK1 & SK2:
(each package = 10 pcs )
Art.No. SK1: 3520054
(2 pins for AC-input)
Art.No. SK2: 3520037
(3 pins for 1x DC-out)
Softstart
30ms typ.
Cooling
Free air convection
Ambient Temperature
- 20°C …+70°C
Storage Temperature
- 40°C …+85°C
EMI
EN55022 class B / EN61000-3-2
EMS
EN61000-6-2,3
Safety
EN60950-1, EN60204-1
Safety class 1(A)
VDE0805, VDE0100
Air & Surface Leakage Paths
> 8mm
Input to Output Isolation
IP-OP: 3kVac IP-GND:2kVac
OP-GND:0.5kVac
MTBF EN61209
300000h
MTTF EN61209.SN29500
125433h @ 40°C 24/7 85% load
Clima/Dirt/Hight/Humidity
3k3, Kl.2, 3000m NN, 90% hum.
ROHS conformity
ROHS Directive 2011/65/EU
REACH conformity
REACH Directive 1907/2006
Dimensions (HxWxD)
28.5x62x96.5mm
Weight
145g
Connectors
SK1 & SK2 not included
Terminal plug AWG26...AWG12
Conception
The OSW power supply series realizes very high power efficiency in a space-saving housing. This design enables Green Power applications
and allows free air convection. Latest generation electrical devices relate to the high reliability of all Camtec products. The Camtec philosophy
is, to employ low ESR ultra long life capacitors where expedient to achieve a superior lifetime of our products. The used screw terminals allow
easy to wire and smooth service. The units perform low ripple & noise. It makes them applicable for sensitive MSR and for Audio systems.
Sense operation
The OSW00751.05 provides sense connections to compensate a voltage drop over the load lines. The maximum compensation is 200mV. Be
aware that this operation mode may recommend extended preparations concerning interference elimination or other protections. We
recommend to use the sense wires twisted. Make sure that the polarization is correct to avoid damages to the power supply. All other
OSW00751 models have no sense connection.
Parallel und series operation
Camtec power supplies of the same model and the same output voltage can be either used parallel or in series. The assembling of external
parts is usually not recommended. Make sure that the output voltage of each connected unit is ±1% equal. We recommend connecting the
DC-outputs to a neutral point or a power bar. Follow the safety norms of dangerous dc-voltages.
UI-Chart, overload and temperature control characteristic
The OSW models base on a typical resonance converter. The converter is ideal for complex loads and DC-drives. Consciously we resigned
an excessive power boost that mostly occurs in less exact working control circuits. The advantage is, that the power supply delivers its energy
always controlled and constant to the load. Even with a faulty operation of the power supply the loads never expose to high risk.
