background image

EMERGENCY DISCONNECT HANDLE 

This handle is located beneath the control console off 
center to the right. When the 

red 

emergency handle is 

pulled, power will be turned off. Use this button in case 
of a machine emergency.  To reactivate, return the 
handle back to its original position, correctly seated in 
the receptacle.  

All operational settings are retained 

even when the power is turned off and on. 

 
 
 
 

CIRCUIT BREAKER 

The circuit breaker is located under the emergency 
belly bar. The 

100-amp breaker

 protects the main 

system circuit (controller). Each main component is 
individually protected with an internal breaker built-
in the controller. (See fault code table) and can be 
reset by turning the key switch off a few seconds 
and then on again. 

 

 

 

 

 

 
 
 

BATTERY COMPARTMENT 

The battery compartment is located 
on the rear of the machine under 
the recovery 

 

tank. Unlatching the two safety 
latches on the side of the machine 
enables the operator 
to tilt the recovery tank and access 
the batteries for servicing and 
maintenance (make sure recovery 
tank has 
been drained before tilting). 
The battery compartment contains 
six 6-volt batteries connected in 
series. Connect 
the batteries according to the 
battery connection diagram 
(

see diagram

). The recommended 

batteries are 275Ah (P/N 956740).

  

 

        

 
 

 

9

Содержание CP 2832



















Отзывы: