background image

Your PowerBass XEX-23 includes a remote Bass Boost Control. It uses standard 6-pin telephone wire and 
modular (U.S.A. style) telephone connectors.  To connect the remote Bass Boost Control to the crossover, 
simply insert one end of the telephone plug into the REMOTE GAIN port.  Plug the other end into the remote 
module.  Install the module within easy reach on or under your dash.

Note: Plugging in the Remote Bass Boost Control overrides the Bass Boost Level Control on the 
XEX-23 chassis.

Notes:

Once the optimum crossover frequencies and output levels are located, mark them down on the chart below 
for future reference in case the settings are accidentally changed.
 
Front Frequency Selector: __________________Hz
Front Frequency Multiplier: x_________________
Rear Frequency Selector: __________________Hz
Rear Frequency Multiplier: x_________________
Bandpass: _________________________ ON or OFF
Subwoofer Input: __________________ SUB or FRONT
Subwoofer Frequency Selector: __________________Hz
Front Output Level: ______________________(o’clock position)
Rear Output Level:  ______________________(o’clock position)
Subwoofer Output Level:  ______________________(o’clock position)

Remote Gain Controller Connection

19

Содержание Xtreme XEX-23

























Отзывы: