Power-Tronics XR500B Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 15

background image

6

19. Input and field circuit are being fed by a common cable or conduit.

20. Incorrect hookup or wiring.

Fuse Replacement

•

Remove the 2 screws located on the front of the mounting can near the

terminal board.

•

Loosen the 2 screws located on the front of the mounting can near the

voltage and stability adjustment holes. (DO NOT REMOVE!)

•

Partially separate the top of the regulator printed circuit card from the

mounting housing. (Separate just enough to reach and replace the fuses)

•

Replace open fuses and re-tighten all screws.

•

Fuse size is 20mm x 5mm, 5 amps @ 250vac.

(DO NOT REPLACE WITH

ANY OTHER TYPE AND RATING OF FUSE! SEVERE DAMAGE AND
PERSONAL INJURY COULD RESULT BY DOING SO!)

«
...
4
5
6
7
8
...
»

Содержание XR500B
















Отзывы:

Нет отзывов

Похожие инструкции для XR500B

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Parker Страницы: 44

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 74

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Samson Страницы: 78

Бренд: Osram Страницы: 3

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Smart Vision Страницы: 5

Бренд: Teledyne Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды