background image

14

TRANSPORT INSTRUCTIONS

It is the responsibility of the transport driver to ensure the Ecolift is 
safely secured to the transport vehicle.

Ensure that the transport vehicle has the load capacity and 
dimensions in order to safely carry the weight and size of the Ecolift.

Ensure that loading straps/chains are of adequate capacity to safely 
secure the Ecolift for transport.

Always ensure that the Ecolift is transported in the upright position. 
Never lay flat.

Ensure the transport vehicle is parked on a level surface and the 
parking brake is applied.

The Ecolift can be loaded via a forklift, tail-lift, or winch. Never push 
the Ecolift up a slope without the aid of a winch.

If using a forklift, raise the Ecolift by approximately 50 - 100mm so that 
the front wheel brakes engage.

Ensure the castor wheel locks are operated and that the forklift tines 
are fully engaged through the chassis sockets.

Load the Ecolift onto the transport vehicle, taking care to position the 
machine so that straps can be located around the base of the machine 
without the need for the driver to have to climb onto the bed of the 
vehicle. Note; only trained qualified forklift drivers are to load the 
Ecolift.

Use at least two straps, with one strap over the chassis, around the 
mast section and out to the rear of the machine. The other strap 
should be fed through the front of the chassis and the straps taken 
forward, so that the machine is tied down in four diagonal directions.
Never place the strap over the platform or handrails.

Loading

 

If loading with the aid of a winch up a ramp to the trailer, connect the 
winch cable to the castor/gate end of the chassis around the tops of 
the swivel castors, and then connect the winch cable to the strap.

Ensure the castor brakes are unlocked, and that the platform is fully 
lowered in the transport position. Before disconnecting the Ecolift 
from the winch cable, engage the castor brake.

If loading with the aid of a tail lift, ensure the tail lift has adequate load 
capacity and dimensions in order to safely lift the Ecolift. Ensure the 
tail lift and vehicle is on flat ground.

TRANSPORTATION, TOWING, LIFTING  AND MANOEUVRING

Courtesy of Crane.Market 

Содержание EcoLift





























Отзывы: