background image

Table of Contents

Hook-up and quick self-test ........................................................................................................... 3

Turning the Audio Tone On & Off ..................................................................................................... 3

Circuit Breaker .............................................................................................................................. 4

Voltage & Polarity testing ............................................................................................................... 5

Continuity testing .......................................................................................................................... 5

Activating components out of vehicle’s electrical system ................................................................ 6

Testing trailer lights and connections.............................................................................................. 7

Activating electrical components in the Vehicle .............................................................................. 8

Activating electrical components with Ground ................................................................................ 9

Checking for bad ground contacts ................................................................................................ 10

Following & Locating Short Circuits .............................................................................................. 10

Red/Green Indicator & Audio Tone ............................................................................................... 10

Flip Screen Function ...................................................................................................................... 10

Modes 1, 2, 3 .............................................................................................................................. 11

Modes 4, 5, Chart ........................................................................................................................ 12

Specifications ............................................................................................................................. 13

Replacement Parts ..................................................................................................................... 14

Power Probe warranty ..................................................................................................... Back Cover

IMPORTANT TIP: When powering-up components, you can increase the life of your Power Probe 

switch if you first press the switch, then contact the tip to the component. The arcing will take place 

at the tip instead of the contacts of the switch.

2

Содержание Power Probe III S

















Отзывы: