1
4
15.
POWER EXTENSION CABLES.
Use only those extension cables that have been manufactured for this purpose and are
marked as appropriately tested and approved.
16.
BE ALERT.
Observe your work. Proceed sensibly. Do not use the tool if you are physically or
mentally impaired in any manner. Do not operate tools under the influence of drugs,
alcohol or medication.
17.
Check Your Tool for Damage.
Before using the tool, carefully check the protective devices for problem-free operation
and intended function. Verify there are no damaged parts. Check whether the function
of moving parts is in order, whether they stick and whether parts are damaged.
DAMAGED PROTECTIVE DEVICES AND PARTS MUST BE PROPERLY REPAIRED
OR REPLACED BY A CUSTOMER-SERVICE WORKSHOP PRIOR TO "TOOL USE".
NEVER USE TOOLS AND SWITCHES THAT CANNOT BE SWITCHED ON AND OFF.
18.
REPAIRS ONLY BY AN ELECTRICAL SPECIALIST.
This power tool complies with all known safety regulations. Only an electrical specialist
may carry out repairs.
19.
USE ONLY ACCESSORIES AND ADDITIONAL DEVICES RECOMMENDED BY THE
TOOL MANUFACTURER.
The use of any insert tools or accessories other than those recommended in the
operating instructions increase risk of injury.
1. If under extreme conditions, any electrolyte should escape from the battery, it is
essential to avoid contact with skin. If electrolyte does come into contact with your
skin, rinse it off with water immediately. In the event of electrolyte contact with your
eyes, consult a physician immediately. Before use of the charger and the Battery
Packet, read the Instruction Manual carefully.
2. Verify the available current corresponds to the current required by the battery charger.
3. Never let moisture, rain, or splashed water reach the charging location.
4. Do not charge your Battery Packet when the temperature is below 10˙C (+ 40˙F) or
above 40˙C(+ 105˙F).
5. Battery packets that are damaged or can no longer be recharged must be disposed of
as hazardous waste. Do not throw the Battery Packet into the trash, into fire, or into
water. Consult your local telephone listing for a battery recycling center in your area.
6. If the electrical cable is damaged, the wire should be replaced by the supplier or by its
authorized repair shop. Repairs should only be made by an authorized specialist.
7. Use only Battery Packets and chargers that have been produced by the original
manufacturer.
DO NOT OTHER BATTERY PACKETS, OR CHARGERS WITH THIS
TOOL
8. Always keep the charger free from dust and dirt.
9. Insert the Battery Packet into the charger. Verify correct polarity before charging.
10. Always remove Battery Packet before working on the tool. Cover the Battery Packet
contacts to avoid short-circuiting the Battery Packet.
11. Avoid the risk of explosion! Do not throw Ni-Cd batteries into water or fire.
12. Protect the Battery Packet from impacts. Do not open packet.
13. Never completely discharge the Battery Packet. Recharge occasionally if Battery
Packet is not in use for a prolonged period.
SPECIAL SAFETY INSTRUCTIONS FOR BATTERY PACKET AND CHARGER
MECHANICAL SPEED REGULATE
MAINTENANCE AND CLEANING:
SPECIFICATIONS
Before doing any work on the tool, always remove the battery pack. Clean the tool with a
moist cloth and a little lubricating soap. Do not use any cleaning agents or solvents these
could attack the plastic parts of the tool. Always keep the surface of the device free from
dust and dirt.
This cordless tool has been manufactured in accordance with the applicable standards and
equipment safety legislation. When using electrical appliances, it is important to take some
safety precautions in order to avoid possible injury and damage. For that reason, you
should carefully read and store these instructions such that this information is available to
you at all times
Technical data
1
2
(
SEE FIGURE 6
)
You can increase the rotate speed by
pushing the regulate button forward.
Position 2: 0-1300 RPM
You can decrease the rotate speed by
pushing the regulate button backwards.
Position 1: 0-425 RPM
High Speed
Low Speed
(FIGURE 6)
18V DC
0~425, 0~1300
3/8 inch, Jacob's Keyless
18V DC; 1.3 Ni-Cd # 60108004
4.55 lbs
60101212
All Metal
Forward, Reverse, Lock
Motor Voltage
No Load Speed
Chuck Size
Battery
Weight
Type
Gears
Controls
Battery Charger
1 - 1.5 Hour, 110/120V ~ 60Hz.
