Powell PowlVac IB-65020A CDR 27kV Скачать руководство пользователя

Страница: 8 / 68

Powered by Safety

IB-65020A

General Information

WARNING

The equipment described in this document may contain high voltages and currents which can

cause serious injury or death.

The equipment is designed for use, installation, and maintenance by knowledgeable users of such

equipment having experience and training in the field of high voltage electricity. This document

and all other documentation shall be fully read, understood, and all warnings and cautions

shall be abided by. If there are any discrepancies or questions, the user shall contact Powell

immediately at 1.800.480.7273.

WARNING

Before any adjustment, servicing, part replacement, or any other act is performed requiring

physical contact with the electrical working components or wiring of this equipment, the power

supply must be disconnected. Failure to follow this warning may result in injury or death.

IMPORTANT

The information in this instruction bulletin is not intended to explain all details or variations of the

equipment, nor to provide for every possible contingency or hazard to be met in connection with

installation, testing, operation, and maintenance of the equipment. For additional information

and instructions for particular problems, which are not presented sufficiently for the user’s

purposes, contact Powell at 1.800.480.7273.

Ch 1 General Information

Powell reserves the right to discontinue and to change specifications at any time without incurring

any obligation to incorporate new features in products previously sold.

IMPORTANT

Содержание PowlVac IB-65020A CDR 27kV





































































Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды

Powell PowlVac IB-65020A CDR 27kV, Руководство пользователя

Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды