Powell PowlVac IB-65020A CDR 27kV Скачать руководство пользователя

Страница: 62 / 68

Powered by Safety

IB-65020A

Recommended Renewal Parts and Replacement Procedures

d. Bolt the new assembly in place and

reconnect it to the wiring harness. No

adjustment is required.

e. Reassemble the connecting rod and

main closing spring, if previously

removed.

f. Trip the circuit breaker several times

electrically to ensure that secondary

shunt trip coil assembly is functioning

properly.

g. Replace the front cover.

5) Undervoltage Device Assembly (UV)

Refer to

SM-1800 Undervoltage Assembly

for

replacement and installation procedures.

6) Charging Motor Assembly

Refer to

SM-1200 Charging Motor

Assembly

for replacement and installation

procedures.

7) Anti-Pump Relay Assembly

Refer to

SM-1000 Anti-Pump Relay

Assembly

for replacement and installation

procedures.

8) Latch Check Switch

Refer to

SM-1400 Latch Check Switch

Assembly & Tripping System Mechanism

Adjustment

for replacement and installation

procedures.

9) Motor Cutoff Switch Assembly

Refer to

SM-1500 Motor Cutoff Switch

Assembly

for replacement and installation

procedures.

10) Auxiliary Switch

Refer to

SM-1100 Auxiliary Switch Assembly

for replacement and installation

procedures.

Содержание PowlVac IB-65020A CDR 27kV





































































Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды

Powell PowlVac IB-65020A CDR 27kV, Руководство пользователя

Результаты поиска

Содержание PowlVac IB-65020A CDR 27kV

Отзывы:

Похожие инструкции для PowlVac IB-65020A CDR 27kV

Бренды по названию

Популярные бренды