background image

5

3. Secure the mounting bracket by tighten-

ing the screws with the hex wrench.

4. Locate the decal on the handlebar. This

decal includes an arrow. Position the

handlebar with the mounting bracket at

the end of the arrow.

5. Position the second bracket cover over

the handlebar. Align the mounting brack-

et and the bracket cover screw holes.

Again make sure the handlebar is at the

end of the arrow.

6. Insert two screws and hand tighten only.

Be sure the handlebar is installed cor-

rectly; then, tighten each screw securely

with the hex wrench.

SHOULDER STRAP ASSEMBLY

WARNING:

Proper shoulder strap

and handlebar adjustments must be made

with the engine completely stopped before us-

ing unit. The shoulder strap clamp must be

installed as shown above the handlebar on the

upper shaft (powerhead end of unit).

NOTE:

The lower shoulder strap clamp has

two spacer tabs attached. These tabs are pro-

vided to adapt this attachment for use with

powerheads that have a 1

(2.5 cm) diameter

upper shaft (the shoulder strap clamp will not

tighten down securely on the 1

(2.5 cm) diam-

eter upper shaft without using these spacer

tabs). The tabs must be broken off completely

before use and placed over the screw holes

on the lower shoulder strap clamp. These tabs

are not needed for powerheads with a 7/8

(2.2 cm) upper shaft.

Spacer Tabs

LOWER SHOULDER STRAP

CLAMP

Spacer Tabs

positioned for use

on 1

(2.5 cm)

diameter

upper shaft

1. Place the upper shoulder strap clamp

over the upper shaft above the handlebar.

2. Position the lower shoulder strap clamp

under the upper shaft and align the upper

and lower clamp screw holes

(use

spacer tabs between upper and lower

clamps if necessary to secure clamp, i.e.

for 1

(2.5 cm) diameter upper shaft).

Upper Shoulder

Strap Clamp

Screws

Lower Shoulder

Strap Clamp

POWERHEAD

END

ATTACHMENT

END

3. Insert two screws into the screw holes.

4. Secure shoulder strap clamp by tighten-

ing screws with the hex wrench.

5. Insert your right arm and head through

the shoulder strap and allow it to rest on

your left shoulder. Make sure the danger

sign is on your back and the hook is to the

right side of your waist.

NOTE:

A one-half twist is built in the shoulder

strap to allow the strap to rest flat on the shoul-

der.

6. Adjust the strap, allowing the hook to be

about 6 inches below the waist.

7. Fasten the strap hook to the clamp and lift

the tool to the operating position.

8. Try on shoulder strap and adjust for fit

and balance before starting the engine or

beginning a cutting operation.

NOTE:

It may be necessary to relocate the

shoulder strap clamp on the shaft for proper

balancing of unit.

30 inches

(76 cm)

HARNESS

ADJUSTMENT

FOR BALANCE

6 inches

(15 cm)

below

waist

4 -- 12

inches

(10 -- 30 cm)

above

ground

30 inches

(76 cm)

Содержание U4000C










Отзывы: