background image

7

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save 

this manual for future reference.

These symbols  may appear on your Tiller or in literature supplied with the product.  Learn and understand their 

meaning.

Fig. 8

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

CHOKE CONTROL

 - Used  when starting a cold engine.

DEPTH STAKE

 - Controls depth at which tiller will dig.

DRIVE CONTROL BAR 

- Used to engage tines.

LEVELING SHIELD

 - Levels tilled soil.

ON / OFF switch -

 used to STOP the engine.

FUEL VALVE 

- Used to turn fuel off and on.

RECOIL STARTER HANDLE

 - Used to start the engine.

SHIFT LEVER

 - Used to shift transmission gears.

SHIFT LEVER INDICATOR

 - Shows which gear the trans-

 mis sion is in.

THROTTLE CONTROL 

- Controls engine speed.

OPERATION

DRIVE

CONTROL

BAR

DEPTH STAKE

SHIFT LEVER

LEVELING

SHIELD

FUEL 

VALVE

ON/OFF 

SWITCH

SHIFT LEVER IN DI CA TOR

THROTTLE CONTROL

CHOKE CONTROL

 

 

 

Содержание Pro PRRT900























Отзывы: