Poulan Pro Pro PRRT900 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 22

Poulan Pro Pro PRRT900 Скачать руководство пользователя страница 6

6

ASSEMBLY

SHIFT

ROD

HAIRPIN

CLIP

SHIFT

LEVER

INDICATOR

REMOVE TILLER FROM CRATE

• Make sure shift lever indicator is in “N” position (See

Fig. 7)

•

Tilt tiller forward by lifting handle. Separate cardboard

cover from leveling shield.

• Rotate tiller handle to the right and pull tiller out of

carton.

CONNECT SHIFT ROD (See Fig. 7)

• Insert end of shift rod into hole of shift lever indicator.
• Insert hairpin clip through hole of shift rod to secure.

Fig. 7

Fig. 6

END OF CLUTCH

CABLE

CONTROL

BAR

CONTROL BAR

BRACKET

CONTROL BAR

BRACKET

CLUTCH

CABLE

ATTACH CLUTCH CABLE (See Fig. 6)

• Hook end of clutch cable through hole in control bar

bracket.

CHECK TIRE PRESSURE

The tires on your unit were overinflated at the factory for

shipping purposes. Correct and equal tire pressure is

important for best tilling performance.
• Reduce tire pressure to 20 PSI (1.4 kg/cm

2

).

HANDLE HEIGHT

•

Handle height may be adjusted to better suit operator.

(See “TO ADJUST HANDLE HEIGHT” in the Service

and Adjustments section of this manual).

«
...
4
5
6
7
8
...
»

Содержание Pro PRRT900























Отзывы:

Нет отзывов