background image

2

IDENTIFICATION OF SYMBOLS

WARNING!

This chain saw

can be dangerous! Careless or

improper use can cause serious

or even fatal injury.

Read and understand the

instruction manual before

using the chain saw.

Always use two hands when operating the chain saw.

WARNING!

Contacting the guide bar tip with any ob-

ject should be avoided; tip contact may cause the guide

bar to move suddenly upward and backward, which may

cause serious injury.

Always wear appropriate

ear protection, eye protec-

tion and head protection.

XX_

Measured maximum kick-

back value without chain

brake for the bar and chain

combination on the label.

Move ON/STOP switch to

the ON position.

Slowly press primer bulb

6 times.

Pull the starter rope

sharply 5 times with your

right hand.

Pull the starter rope sharply

with your right hand until

the engine starts.

Pull choke/fast idle lever

out to the full extent (to

the FULL CHOKE posi-

tion).

Push the choke/fast idle

lever in to the HALF

CHOKE position.

Starting Reminder

Chain Tensioning

Lift lever on bar knob and

turn counterclockwise 1 turn

to loosen bar clamp.

Turn adjusting wheel (downward

direction) to tension chain until

chain solidly contacts bottom of

guide bar rail.

While lifting tip of guide bar, tight-

en bar knob (clockwise) securely.

Hand tighten only!

Return lever

on bar knob to original position.

Содержание PP3516AVX





















Отзывы: