background image

27

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    198584            Screw, Hex Head  5/16-18 x 3/4
   2    751153            Nut, Lock  5/16-18
   4    198584            Screw, Hex Head  5/16-18 x 1/2
   5    180017            Bearing, Flange
   6    180134            Shaft, Auxiliary
   7    179270            Spacer, Plate
   8    192616X479    Plate, Auxiliary
   9    180082            Gear, Intermediate (12/58)

10    180065            Gear, Pinion

 11    187714            Rod, Clutch

12    180066            Shaft, Long, Hex
13    178807            Pin, Pivot
14    178619X479    Lever, Shifter / Wheel
15    175344            Trunnion Bearing Assembly
16    186951X479    Bracket, Pivot, Shifter
17    179831            Ring, Rubber Wheel
18    198176X479    Plate, Rubber Wheel
19    73930500        Nut, Lock  5/16-18
20    178613            Hub, Rubber Wheel
21    74760514        Screw, Hex Head  5/16-18 x 7/8
22    85179              Retainer, Hairpin
23    180135            Spring, Bias
24    180081            Gear, Axle (58 Teeth)
25    178695            Pin, Pivot Lever
26    197763            Plate Assembly, Drive
27    404307            Shaft, Axle
28    197764            Shaft, Short Hex
29    175350X479    Lever, Shifter Plate
30    175349X479    Bracket, Shifter Support
31    72270505        Bolt, Carriage  5/16-18 x 5/8
32    189282            Key, Square  1/4 x 1/4 x 7/8
33    188909            Bearing, Flange
34    175338X479    Plate, Drive Mounting
35    182504            Spacer, Bearing
36    191080            Pulley, Traction Drive
37    198541            Nut, Lock  5/16-18
38    19111507         Washer, Flat
39    198552            Washer, Lock 5/16
40    74950512        Screw, Hex Head  5/16-18 x 3/4
41    12000012        Ring, Retaining
43    179095            Spring, Return
44    9465M             Pin, Roll

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP10530ES

  (96192001200)

DRIVE

NOTE:  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your unit and void your warranty.

Содержание PP10530ES

































Отзывы: