background image

13

GENERAL REC OM MEN DA TIONS

The warranty on this snow thrower does not cover items 

that have been sub ject ed to operator abuse or negligence.  

To receive full value from the warranty, operator must 

maintain snow thrower as in struct ed in this manual.  Some 

ad just ments will need to be made periodically to properly 

maintain your snow thrower.  All adjustments in the Service 

and Ad just ments section of this manual should be checked 

at least once each season.
•  Once a year, you should replace the spark plug and 

check belts for wear.  A new spark plug will help your 

engine run better and last longer.

•  Follow the maintenance schedule in this manual.

NOTE:

 Use only Original Equipment Manufacturer (OEM) 

parts to service this unit.  Failure to do so can cause the unit 

to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.  Check engine oil level.
2.  Check for loose fasteners.
3.  Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated

(See “LU BRI CA TION CHART”).

MAINTENANCE

LUBRICATION CHART

SNOW THROWER

Always observe the safety rules when performing any 

main te nance.

TIRES

• 

Maintain proper air pressure in both tires (14–17 P.S.I.)

• 

Keep tires free of gasoline and oil, which can harm rubber.

NOTE:

 To seal tire punctures and prevent flat tires due 

to slow leaks, tire sealant may be purchased from your 

local parts dealer. Tire sealant also prevents tire dry rot 

and cor ro sion.

 

SAE 5W-30 Motor Oil

 

See “ENGINE”

in Maintenance

section

 

General

     Purpose

     Grease

Engine oil

 

Pivot 

points

BELTS

Check belts for deterioration and wear after every 50 hours 

of operation and replace if necessary. The belts are not 

ad just able. Replace belts if they begin to slip from wear. 

(See “TO REMOVE BELT COVER” in the Service and 

Adjustments section of this manual).
The belts on your snow thrower are of special con struc tion 

and should be replaced by original equipment man u fac tur er 

(OEM) belts avail able from your nearest dealer. Using other 

than OEM belts can cause personal injury or damage to 

the snow thrower.

 

Auger

grease fittings

Содержание 96192003300









































Отзывы: