background image

20

PRO authorized repair center as soon as a

problem exists. Warranty repairs should be

completed in a reasonable amount of time, not

to exceed 30 days. If you have any questions

regarding your warranty rights and responsi-

bilities, you should contact your nearest autho-

rized service center, call Poulan PRO at

1--800--554--6723, or send e-mail corre-

spondence to emission.warranty@HCOP--

emission.com.

WARRANTY COMMENCE-

MENT DATE:

The warranty period begins

on the date the small off--road engine is pur-

chased.

LENGTH OF COVERAGE:

This

warranty shall be for a period of two years

from the initial date of purchase, or until the

end of the product warranty (whichever is

longer).

WHAT IS COVERED: REPAIR OR

REPLACEMENT OF PARTS.

Repair or re-

placement of any warranted part will be per-

formed at no charge to the owner at an ap-

proved Poulan PRO servicing center. If you

have any questions regarding your warranty

rights and responsibilities, you should contact

your nearest authorized service center, call

Poulan PRO at 1--800--554--6723, or send

e-mail correspondence to emission.warranty

@HCOP--emission.com.

WARRANTY PE-

RIOD:

Any warranted part which is not

scheduled for replacement as required

maintenance, or which is scheduled only for

regular inspection to the effect of “repair or

replace as necessary” shall be warranted for

2 years. Any warranted part which is sched-

uled for replacement as required mainte-

nance shall be warranted for the period of

time up to the first scheduled replacement

point for that part.

DIAGNOSIS:

The owner

shall not be charged for diagnostic labor

which leads to the determination that a war-

ranted part is defective if the diagnostic work

is performed at an approved Poulan PRO

servicing center.

CONSEQUENTIAL DAMAGES:

Poulan

PRO may be liable for damages to other en-

gine components caused by the failure of a

warranted part still under warranty.

WHAT IS

NOT COVERED

: All failures caused by

abuse, neglect, or improper maintenance

are not covered.

ADD--ON OR MODIFIED

PARTS:

The use of add--on or modified parts

can be grounds for disallowing a warranty

claim. Poulan PRO is not liable to cover fail-

ures of warranted parts caused by the use of

add--on or modified parts.

HOW TO FILE A

CLAIM:

If you have any questions regarding

your warranty rights and responsibilities,

you should contact your nearest authorized

service center, call Poulan PRO at

1--800--554--6723, or send e-mail corre-

spondence to emission.warranty@HCOP--

emission.com.

WHERE TO GET WARRAN-

TY SERVICE:

Warranty services or repairs

shall be provided at all Poulan PRO service

centers. Call: 1--800--554--6723 or send e-mail

correspondence

to

emission.warranty@

HCOP--emission.com.

MAINTENANCE,

REPLACEMENT AND REPAIR OF EMIS-

SION RELATED PARTS

: Any Poulan PRO

approved replacement part used in the per-

formance of any warranty maintenance or

repair on emission related parts will be pro-

vided without charge to the owner if the part

is under warranty.

EMISSION CONTROL

WARRANTY PARTS LIST:

Carburetor, air fil-

ter (covered up to maintenance schedule), igni-

tion system: spark plug (covered up to mainte-

nance schedule), ignition module, muffler

including catalyst (if equipped), fuel tank.

MAINTENANCE STATEMENT:

The owner

is responsible for the performance of all re-

quired maintenance as defined in the in-

struction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Содержание 952802030





















Отзывы: