background image

2

IDENTIFICATION OF SYMBOLS

WARNING!

This chain saw

can be dangerous! Careless or

improper use can cause serious

or even fatal injury.

Read and understand the

instruction manual before

using the chain saw.

Always use two hands when operating the chain saw.

WARNING!

Contacting the guide bar tip with any ob-

ject should be avoided; tip contact may cause the guide

bar to move suddenly upward and backward, which may

cause serious injury.

Always wear appropriate

ear protection, eye protec-

tion and head protection.

XX_

Measured maximum kick-

back value without chain

brake for the bar and chain

combination on the label.

Move ON/STOP switch to

the ON position.

Slowly press primer bulb

6 times.

Pull the starter rope

sharply 5 times with your

right hand.

Pull the starter rope sharply

with your right hand until

the engine starts.

Pull choke/fast idle lever

out to the full extent (to

the FULL CHOKE posi-

tion).

Push the choke/fast idle

lever in to the HALF

CHOKE position.

Starting Reminder

SAFETY RULES

WARNING:

Always disconnect

spark plug wire and place wire where it can-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this tool can

cause serious injury.

PLAN AHEAD

S

Read this manual carefully until you com-

pletely understand and can follow all safety

rules, precautions, and operating instruc-

tions before attempting to use the unit.

S

Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

S

Wear protective gear. Always use steel-

toed safety footwear with non-slip soles;

snug-fitting clothing; safety chaps; heavy-

duty, non-slip gloves; eye protection such

as non-fogging, vented goggles or face

screen; an approved safety hard hat; and

sound barriers (ear plugs or mufflers) to

protect your hearing.

Regular users

should have hearing checked regularly as

chain saw noise can damage hearing. Se-

cure hair above shoulder length.

Содержание 952802030





















Отзывы: