Poulan Pro 545186803 Скачать руководство пользователя

Страница: 16 / 20

Turn idle speed screw (T) counterclock-

wise to decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized

service

dealer

call

1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be neces-

sary to service your bar. A worn bar will dam-

age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is

in the STOP position, then clean all sawdust

from the guide bar and sprocket hole.
To maintain guide bar:

Move ON/STOP switch to the STOP posi-

tion.

Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

Clean the oil holes and bar groove after each

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

Burring of guide bar rails is a normal

process of rail wear. Remove these burrs

with a flat file.

When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct Groove

Worn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when

excess heating or burring of the rails occurs.

If replacement is necessary, use only the guide

bar specified for your saw in the repair parts list

or on the decal located on the chain saw.

CHAIN SHARPENING

WARNING:

Improper chain sharp-

ening techniques and/or depth gauge mainte-

nance will increase the chance of kickback

which can result in serious injury.

WARNING:

Wear protective gloves

when handling chain. The chain is sharp and

can cut you even when it is not moving.

Conditions which indicate the need for chain

sharpening:

Reduction in size of wood chips. The size

of the wood chip will decrease as the chain

gets duller until it becomes more like a

powder than a chip. Note that dead or

rotted wood will not produce a good chip.

Saw cuts to one side or at an angle.

Saw has to be forced through the cut.

Tools required:

5/32 inch (4 mm) diameter round file and

file holder

Flat file

Depth gauge tool

TO SHARPEN CHAIN:

1. Move ON/STOP switch to the STOP

position.

2. Check chain for proper tension. Adjust

chain tension if necessary. See CHAIN

TENSION section.

3. Sharpen cutters.

To sharpen the cutters, position the

file holder level (90

) so that it rests

on the top edges of the cutter and

depth gauge.

NOTE:

The chain has both left and

right hand cutters.

Depth Gauge

File

File Holder

Cutter

Align the 30

file holder marks paral-

lel with the bar and to the center of the

chain.

Cutter

File Holder Line

Sharpen cutters on one side of the

chain first. File from the inside of each

cutter to the outside. Then, turn the

chain saw around and repeat the pro-

cess for the other side of the chain.

File on the forward stroke only. Use 2

or 3 strokes per cutting edge.

Keep all cutters the same length

when filing.

File enough to remove any damage

to cutting edges (side plate and top

plate of cutter).

All Cutters

Same Length

Remove Damage

Top Plate

Side Plate

File chain to meet the specifications

as shown.

Содержание 545186803





















Результаты поиска

Содержание 545186803

Отзывы:

Похожие инструкции для 545186803

Бренды по названию

Популярные бренды

Poulan Pro 545186803, Инструкция по эксплуатации

Результаты поиска

Содержание 545186803

Отзывы:

Похожие инструкции для 545186803

Бренды по названию

Популярные бренды