background image

18

SERVICE AND ADJUSTMENTS

STORAGE

Immediately prepare your unit for storage at the end of the 
season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow 
thrower with gaso line in the tank in side 
a build ing where fumes may reach an 
open fl ame, spark or pilot light as on a 
fur nace, water heater, clothes dryer or 
gas ap pli ance.  Allow the engine to cool 
be fore storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, 
clean it thor oughly, re move all dirt, grease, leaves, etc. 
Store in a clean, dry area.

1.   Clean entire snow thrower (See “CLEANING” in the 

Main te nance section of this manual).

2.    Inspect and replace belts, if necessary (See “TO RE-

 PLACE BELTS” in the Service and Adjustments sec tion 
of this manual).

3.    Lubricate as shown in the Main te nance sec tion of this 

man u al.

4.      Be sure that all nuts, bolts, screws, and pins are securely 

fas tened. Inspect moving parts for damage, breakage 
and wear. Replace if nec es sary.

5.   Touch up all rusted or chipped paint surfaces; sand 

lightly before painting.

ENGINE

See engine manual.

FUEL SYS TEM

IMPORTANT

:  It is important to prevent gum deposits from 

forming in essential fuel system parts such as carburetor,  
fuel hose, or tank during storage. Also, alcohol blended fuels 
(called gasohol or using ethanol or methanol) can attract 
moisture which leads to separation and formation of acids 
during storage. Acidic gas can damage the fuel system of 
an engine while in storage.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance 
should not be affected at altitudes up to 7,000 feet (2,134 
meters). If your engine does not operate properly due to 
suspected carburetor problems, take your snow thrower to 
a qualifi ed service center.

•      Empty the fuel tank by starting the engine and letting 

it run until the fuel lines and car bu re tor are empty.

•         Never use engine or carburetor cleaner prod ucts in the 

fuel tank or permanent damage may occur.

•      Use fresh fuel next season.

NOTE: 

 Fuel stabilizer is an acceptable alternative in min-

 i miz ing the formation of fuel gum deposits during stor age. 
Add stabilizer to gasoline in fuel tank or storage container. 
Always follow the mix ratio found on stabilizer container. 
Run engine at least 10 min utes after adding stabilizer to 
allow the stabilizer to reach the carburetor. Do not drain the 
gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of 
this man ual).

CYLINDER

1.    Remove spark plug.

2.    Pour one ounce (29 ml) of oil through spark plug hole 

into cylinder.

3.      Pull recoil starter handle slowly a few times to dis trib ute 

oil.

4.    Replace with new spark plug.

OTHER

•      Do not store gasoline from one season to another.

•     Replace your gasoline can if your can starts to rust. 

Rust and/or dirt in your gasoline will cause problems.

•      If possible, store your snow thrower indoors and cover 

it to protect it from dust and dirt.

•         Cover your snow thrower with a suitable pro tec tive cover 

that does not retain moisture. Do not use plastic. Plastic 
cannot breathe, which allows con den sa tion to form and 
will cause your snow thrower to rust.

IMPORTANT

: Never cover snow thrower while engine/

exhaust area is still warm.

ENGINE SPEED

Never tamper with the engine governor, which is factory set 
for proper engine speed. Overspeeding the engine above 
the factory high speed setting can be dangerous and will 
void the warranty. If you think the engine-governed high 
speed needs adjusting, contact a qualifi ed service center, 
which has proper equipment and experience to make any 
necessary ad just ments.

Содержание 199338





















Отзывы: