Poulan Pro 191663 Скачать руководство пользователя | Manualshive

Страница: 28 / 32

background image

28

Will not start

1. Out of fuel. 1. Fill fuel tank.

2.   Engine not “CHOKED”    2.   See “TO START ENGINE” in
   properly.     Operation section.
3.   Engine fl ooded.   3.   Wait several minutes before
   attempting to start.
4.   Bad spark plug. 4.   Replace spark plug.
5.   Dirty air fi lter. 5.   Clean/replace air fi lter.
6.   Dirty fuel fi lter.   6.   Replace fuel fi lter.
7.   Water in fuel. 7.   Empty fuel tank and carbure-
  tor, refi ll tank with fresh gaso-
  line and replace fuel fi lter.
8.   Loose or damaged wiring. 8.   Check all wiring.
9.   Carburetor out of adjustment.  9.   See “To Adjust Carburetor”
   in Service and Adjustments
   section.
10. Engine valves out of   10. Contact our authorized
   adjustment.      service center/department.

Hard to start

1. Dirty air fi lter. 1. Clean/replace air fi lter.

2.   Bad spark plug. 2.   Replace spark plug.
3.   Weak or dead battery. 3.   Recharge or replace battery.
4.   Dirty fuel fi lter.   4.   Replace fuel fi lter.
5.   Stale or dirty fuel.   5.   Empty fuel tank and refi ll tank
with fresh, clean gasoline.
6.   Loose or damaged wiring. 6.   Check all wiring.
7.   Carburetor out of adjustment.  7.   See “To Adjust Car bu re tor”
   in Service and Ad just ments
   sec tion.
8.   Engine valves out of   8.   Contact our authorized
   adjustment.      service center/department.

Engine will not

1. Brake pedal not depressed. 1. Depress brake pedal.

turn over

2. At tach ment clutch is engaged. 2. Disengage attachment clutch.

3.   Weak or dead battery. 3.   Recharge or replace battery.
4.   Blown fuse.   4.   Replace fuse.
5.   Corroded battery terminals.     5.   Clean battery terminals.
6.   Loose or damaged wiring. 6.   Check all wiring.
7.   Faulty ignition switch.     7.   Check/replace ignition switch.
8.   Faulty solenoid or starter.   8.   Check/replace solenoid or
   starter.
9.   Faulty operator presence    9.   Contact our authorized
   switch(es).    service center/department.

Engine clicks but

1. Weak or dead battery. 1. Re charge or replace battery.

will not start

2. Corroded battery terminals. 2. Clean battery terminals.

3.   Loose or damaged wiring. 3.   Check all wiring.
4.   Faulty solenoid or starter.   4.   Check/replace solenoid or
   starter.

Loss of power

1. Cutting too much grass/too 1. Raise cutting height/reduce

   fast.      speed.
2.   Throttle in “CHOKE” position. 2.   Adjust throttle control.
3.   Build-up of grass, leaves and  3.   Clean underside of mower
   trash under mower.      housing.

4. Dirty air fi lter. 4. Clean/replace air fi lter.

PROBLEM CAUSE CORRECTION

TROUBLESHOOTING CHART:

«
...
26
27
28
29
30
...
»

Содержание 191663

































Отзывы:

Нет отзывов

Похожие инструкции для 191663

Бренд: Jacobsen Страницы: 108

Бренд: Gravely Страницы: 52

Бренд: Oleo-Mac Страницы: 344

Бренд: LawnMaster Страницы: 31

Бренд: Powersmart Страницы: 22

Бренд: Swift Страницы: 7

Бренд: Mean Green Products Страницы: 30

GrandStand 74567TE

Бренд: Toro Страницы: 64

Бренд: Tecumseh Страницы: 20

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 6

Бренд: Cub Cadet Страницы: 40

Бренд: Cub Cadet Страницы: 52

Бренд: Cub Cadet Страницы: 72

Бренд: Cub Cadet Страницы: 112

Бренд: Wolf Garten Страницы: 126

Super Recycler 21383

Бренд: Toro Страницы: 32

Бренд: Exmark Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды