Poulan Pro 188870 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 44

background image

7

ASSEMBLY

FIG. 2

TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and func tion of
con trols)

• Press lift lever plunger and raise attachment lift lever

to its highest po si tion.

• Release parking brake by depressing clutch/brake

ped al.

•      Place gearshift lever in neutral (N) po si tion.
•      Roll tractor forward off skid.
•     Remove banding holding defl ector shield up against

tractor.

TO DRIVE TRACTOR OFF SKID (See Op-
er a tion sec tion for lo ca tion and func tion of
con trols)

WARNING:

Before starting, read, un der stand and follow

all in struc tions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
• Be sure all the above assembly steps have been com-

pleted.

• Check engine oil level and fi ll fuel tank with gasoline.
• Sit on seat in operating position, depress clutch/brake

pedal and set the parking brake.

• Place gear shift lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever

to its highest position.

• Start the engine. After engine has started, move throttle

control to idle position.

• Depress clutch/brake pedal into full “BRAKE” position

and hold. Move gearshift lever to 1st gear.

• Slowly release clutch/brake pedal and slowly drive

tractor off skid.

• Apply brake to stop tractor, set parking brake and place

gearshift lever in neutral position.

• Turn ignition key to “OFF” position.
Continue with the instructions that follow.

FIG. 3

CHECK BATTERY (See Fig. 3)

• Lift seat pan to raised position.
• If this battery is put into service after month and year

indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

ADJUSTMENT
BOLT

LOCK WASHER

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.
• Remove adjustment bolt, lock washer and fl at washer

se cur ing seat to cardboard packing and set aside for
as sem bly of seat to tractor.

• Pivot seat upward and remove from the cardboard pack-

ing. Remove the cardboard packing and discard.

• Place seat on seat pan so head of shoulder bolt is

positioned over large slotted hole in pan.

• Push down on seat to engage shoulder bolt in slot and

pull seat towards rear of tractor.

• Pivot seat and pan forward and assemble adjust-

ment bolt, lockwasher and fl at washer loosely. Do not
tighten

• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached

which allows you to press clutch/brake pedal all the
way down.

• Get off seat without moving its adjusted position.
• Raise seat and tighten adjustment bolt securely.

SEAT PAN

SHOULDER
BOLT

FLAT WASHER

SEAT

NOTE:

You may now roll or drive your tractor off the skid.

Follow the appropriate instruction below to remove the
tractor from the skid.

«
...
5
6
7
8
9
...
»

Содержание 188870













































Отзывы:

Нет отзывов

Похожие инструкции для 188870

Бренд: Lawn-Boy Страницы: 84

Бренд: Bestgreen Страницы: 88

Jacobsen SLF530

Бренд: Textron Страницы: 352

Бренд: Hayter Страницы: 56

Бренд: elem Страницы: 99

Бренд: Toro Страницы: 72

Бренд: Mountfield Страницы: 14

Бренд: Weed Eater Страницы: 13

Бренд: Snapper Страницы: 44

Бренд: MasterCraft Страницы: 15

Бренд: Mogatec Страницы: 80

Бренд: Dixon Страницы: 32

Бренд: Dixon Страницы: 35

Бренд: Dixon Страницы: 36

DX254 / 966651201

Бренд: Dixon Страницы: 68

Бренд: Dixon Страницы: 68

Бренд: Dixon Страницы: 20

Бренд: Craftsman Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды