Poulan Pro 188870 Скачать руководство пользователя | Manualshive

Страница: 6 / 44

background image

6

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Stan dard
wrench sizes are listed.
(2) 7/16" wrenches

Utility knife

(2) 3/4" wrench

Tire pres sure gauge

Pliers
When right or left hand is mentioned in this man ual, it means
when you are in the operating po si tion (seated be hind the
steer ing wheel).

TO REMOVE TRACTOR FROM
CAR TON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons

from carton.

• Cut along dotted lines on all four panels of carton.

Remove end panels and lay side panels fl at.

• Check for any additional loose parts or cartons and

remove.

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.

FIG. 1

1/4 LOCKNUT

LOWER
STEERING
SHAFT

STEERING
BOOT

EXTENSION SHAFT

1/4 HEX BOLT

STEERING
WHEEL

INSERT

ADAPTER

1/2 HEX NUT

LARGE FLAT
WASHER

TABS

TAB
SLOTS

BEFORE REMOVING TRACTOR FROM
SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT
• Slide extension shaft onto lower steering shaft. Align

mount ing holes in extension and lower shafts and install
1/4 hex bolt and lock nut. Tighten securely.

IMPORTANT:

TIGHTEN BOLT AND NUT SECURELY TO

10-12 FT. LBS TORQUE.
• Place tabs of steering boot over tab slots in dash and

push down to secure.

INSTALL STEERING WHEEL
• Position front wheels of the tractor so they are pointing

straight forward.

• Remove steering wheel adapter from steering wheel

and slide adapter onto steer ing shaft ex ten sion.

• Position steering wheel so cross bars are hor i zon tal

(left to right) and slide inside boot and onto adapt er.

• Assemble large fl at washer, 1/2 hex nut and tighten

se cure ly.

• Snap steering wheel insert into center of steer

ing

wheel.

• Remove protective materials from tractor hood and

grill.

IMPORTANT:

CHECK FOR AND RE MOVE ANY STA PLES

IN SKID THAT MAY PUNC TURE TIRES WHERE TRACTOR
IS TO ROLL OFF SKID.

«
...
4
5
6
7
8
...
»

Содержание 188870













































Отзывы:

Нет отзывов

Похожие инструкции для 188870

Бренд: Cub Cadet Страницы: 32

Бренд: MTD Страницы: 28

Бренд: Toro Страницы: 8

Бренд: Montgomery Ward Страницы: 8

Бренд: Smithco Страницы: 114

Бренд: Walker Страницы: 92

Tri King 1900 Series

Бренд: Jacobsen Страницы: 30

Бренд: Woods Страницы: 28

Бренд: Snapper Страницы: 56

Бренд: Snapper Страницы: 20

Throw Reel Mower

Бренд: Mclane Страницы: 16

Бренд: Mountfield Страницы: 50

Бренд: Scag Power Equipment Страницы: 18

Бренд: Brill Страницы: 104

Бренд: Craftsman Страницы: 60

Бренд: Cub Cadet Страницы: 48

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды