Poulan Pro 183188 Скачать руководство пользователя

Страница: 7 / 48

ASSEMBLY

TO ROLL TRACTOR OFF SKID (See Opera-
tion section, page 10, for location and func-
tion of controls)

•

Press lift lever plunger and raise attachment lift lever to
its highest position.

•

Release parking brake by depressing clutch/brake pedal.

•

Place gearshift lever in neutral (N) position.

•

Roll tractor forward off skid.

•

Remove banding holding deflector shield up against
tractor.

FIG. 3

ADJUSTMENT
BOLT

LOCK WASHER

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment bolt.
•

Remove adjustment bolt, lock washer and flat washer
securing seat to cardboard packing and set aside for
assembly of seat to tractor.

•

Pivot seat upward and remove from the cardboard
packing. Remove the cardboard packing and discard.

•

Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.

•

Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.

•

Pivot seat and pan forward and assemble adjustment
bolt, lockwasher and flat washer loosely. Do not tighten

•

Lower seat into operating position and sit on seat.

•

Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way down.

•

Get off seat without moving its adjusted position.

•

Raise seat and tighten adjustment bolt securely.

SEAT PAN

SHOULDER
BOLT

FLAT WASHER

SEAT

NOTE:

You may now roll or drive your tractor off the skid.

Follow the appropriate instruction below to remove the
tractor from the skid.

TO DRIVE TRACTOR OFF SKID (See Opera-
tion section, page 10, for location and func-
tion of controls)

WARNING:

Before starting, read, understand and follow

all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
•

Be sure all the above assembly steps have been
completed.

•

Check engine oil level and fill fuel tank with gasoline.

•

Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.

•

Place gear shift lever in neutral (N) position.

•

Press lift lever plunger and raise attachment lift lever to
its highest position.

•

Start the engine. After engine has started, move throttle
control to idle position.

•

Depress clutch/brake pedal into full "BRAKE" position
and hold. Move gearshift lever to 1st gear.

•

Slowly release clutch/brake pedal and slowly drive
tractor off skid.

•

Apply brake to stop tractor, set parking brake and place
gearshift lever in neutral position.

•

Turn ignition key to "OFF" position.

Continue with the instructions that follow.

Содержание 183188

















































Результаты поиска

Содержание 183188

Отзывы:

Похожие инструкции для 183188

Бренды по названию

Популярные бренды

Poulan Pro 183188, Руководство оператора

Результаты поиска

Содержание 183188

Отзывы:

Похожие инструкции для 183188

Бренды по названию

Популярные бренды