Potter Intelligen INS-2500 Скачать руководство пользователя

Страница: 4 / 57

INS-2500 • 5403680 • REV C • 04/19

This manual contains safety information that is important to know and understand. This

information is provided for the safety of installers, operators, and users of the Potter

Nitrogen Generator as well as equipment. To help recognize this information, observe the

following symbols.

Safety Guidelines

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury

Notice indicates important information, that if not followed may cause damage to equipment or property.

CAUTION

Important Notice to Users

The Installation, Operation, and Instruction Manual supplied with each unit must be read thoroughly and completely understood

before installation and operation of the Potter IntelliGen

™

Nitrogen Generator. All appropriate safety standards for handling of

gases as determined by local or national laws and regulations should be followed at all times.

Unpacking

After unpacking unit, carefully inspect all parts and equipment for any damage that may have occurred during transit. Make sure

to tighten fittings, bolts, etc. before putting unit into service.

Do not operate if damage occurred during shipping, handling, or

use. Contact Potter immediately.

General Safety Information

Important: Read all of the safety information in this manual before operating this equipment. Use of the equipment in a manner

not specified within this manual may impair the protection provided by the generator and could result in an unplanned release of

pressure, which may cause serious injury or damage. Only competent personnel, who have been trained, qualified, and approved

by Potter Electric Signal Company should perform commissioning, servicing, and repair procedures.

When handling, installing, or operating this equipment, personnel must employ safe engineering practices and observe all related

local regulations, health, and safety procedures, and legal requirements for safety. Ensure that the equipment is depressurized and

electrically isolated, before carrying out any of the scheduled maintenance instructions specified in this manual.

Содержание Intelligen INS-2500


























































Результаты поиска

Содержание Intelligen INS-2500

Отзывы:

Похожие инструкции для Intelligen INS-2500

Бренды по названию

Популярные бренды

Potter Intelligen INS-2500, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Intelligen INS-2500

Отзывы:

Похожие инструкции для Intelligen INS-2500

Бренды по названию

Популярные бренды