background image

FCC Notice  

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation. 
 
This equipment may generate, use and/or radiate radio frequency energy. If not installed and used in 
full  accordance  with  this  User’s  Manual,  interference  to  radio  communications  may  occur.  This 
equipment  complies  with  the  limits  for  a  Class A  Information  Technology  Equipment  pursuant  to 
Part  15  of  the  FCC  Rules,  which  are  designed  to  provide  reasonable  protection  against  such 
interference  when  operated  in  a  commercial  environment.  Operation  of  this  equipment  in  a 
residential  area  may  also  cause  interference.  In  such  case  the  user,  at  his/her  expense,  will  be 
required to correct the interference using whatever means necessary. 

 

Trademarks 

POSTEK is a registered trademark by POSTEK Electronics Co., Ltd.   
ARM is a registered trademark of Advanced RISC Machines Ltd. 
Microsoft, Windows are registered trademarks of Microsoft Corporation. 

 

Copyright 

© 2021 by Postek Electronics Co., Ltd. All rights reserved. Under the copyright laws, this manual 
cannot  be  reproduced  in  any  form  without  the  prior  written  permission  of  POSTEK.  No  patent 
liability is assumed, with respect to the use of the information contained herein. 
 

Disclaimer 

POSTEK  barcode/RFID  printers  are  developed  and  produced  by  Postek  Electronics  Co.,  Ltd 
(hereinafter as “POSTEK”) with the adoption of direct thermal/thermal transfer printing and RFID 
encoding  techniques.  For  thermal  transfer  printing,  matching  ribbons  and  media  are  required. 
Meanwhile, the wide variety of RFID chip and antenna designs make it difficult to guarantee RFID 
tag’s 100% compatibility with POSTEK printers, to satisfy your printing needs, please consult with 
the local reseller(s) to choose the matching consumables for POSTEK printers. 
 
This  manual  has  been  validated  and  reviewed  for  accuracy.  The  instructions  and  descriptions  it 
contains are  accurate for the POSTEK printer  at  the time of this manual’s distribution. However, 
succeeding printers and manuals are subject to change without notice. POSTEK assumes no liability 
for  damages  incurred  directly  or  indirectly  from  errors,  omissions  or  discrepancies  between  the 
printer and this manual. 
 
To  protect  your  interest,  and  to  prevent  loss  due  to  improper  handling,  please  read  the 

Содержание iQ200







































Отзывы: