background image

Page 3

For technical questions, please call 1-888-866-5797.

Item 56808 
        

SaFEty

OpEra

tiOn

MaintEnancE

aSSEMbl

y

Extension cord Size

The following table shows the correct cord 
size to use depending on cord length and 
nameplate ampere rating.  If in doubt, use 
the next heavier gauge.  The smaller the 
gauge number, the heavier the cord. 

tablE a – MiniMUM WirE GaUGE FOr 

EXtEnSiOn cOrDS

 (120 VOlt)

ampere rating

(at full load)

EXtEnSiOn cOrD lEnGtH

25′

50′

100′

150′

0 – 6

18

16

16

14

6 – 10

18

16

14

12

10 – 12

16

16

14

12

12 – 16

14

12

Not recommended

connecting cords

To reduce the risk of the cords pulling apart 
during operation, do one of the following: 

a.  Make a knot as shown below 

then connect the cords:

b. 

Extension 

cord

appliance 

cord

1

2

Or, use a plug-receptacle retaining 

strap or connector designed to hold 
extension cords to appliance cords.

personal Safety

1. 

Dress properly -

 Do not wear loose clothing or 

jewelry.  They can be caught in moving parts.  
Use of rubber gloves and substantial footwear 
is recommended when working outdoors.  
Wear protective hair covering to contain long hair.

2. 

          

Wear anSi-approved safety goggles,  

hard hat and heavy-duty rubber work 
gloves. 

 Use face or dust mask if 

operation is dusty.

3. 

avoid Unintentional Starting -

  

Do not carry plugged-in appliance with finger on 
switch.  Be sure switch is off when plugging in.

4. 

Do not Overreach - 

Keep proper footing and balance at all times.

5. 

Stay alert -

 Watch what you are doing. Use 

common sense.  Do not operate appliance when 
you are tired.

6. 

DanGEr! people with pacemakers should 
not use pole saws.  

Pole saws produce 

strong electromagnetic fields that can cause 
pacemaker interference or pacemaker failure.  
People with pacemakers should consult 
their physician(s) for advice.

Gardening appliance Use and care

1. 

avoid Dangerous Environment -  

Do not use appliances in damp or wet locations.

2. 

Do not Use in rain.

3. 

Keep children away -

 All visitors should 

be kept at a distance from work area.

4. 

When servicing use only identical 
replacement parts.

5. 

Use right appliance -

 Do not use appliance 

for any job except that for which it is intended.

6. 

Do not Force appliance - 

It will do the 

job better and with less likelihood of injury 
at the rate for which it was designed.

7. 

Store idle appliances indoors - 

When not in use, 

appliances should be stored indoors in dry, and 
high or locked-up place - out of reach of children.

8. 

Disconnect appliance - 

Disconnect the 

appliance from the power supply when not 
in use, before servicing, when changing 
accessories such as blades, and the like.

Содержание 56808

















Отзывы: