background image

13

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant
for the life of the unit under normal operating conditions. No further
lubrication is necessary.

BRUSH INSPECTION AND LUBRICATION

For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA
FACTORY SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have
new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO
OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is
present, return your tool to the service station for immediate service.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA
FACTORY SERVICE CENTER. All repairs made by these agencies are fully
guaranteed against defective material and workmanship. We cannot
guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.). 

ACCESSORIES

A complete line of accessories is available from your Porter-Cable 

Delta Supplier, Porter-Cable 

Delta Factory Service Centers, and

Porter-Cable Authorized Service Stations. Please visit our Web Site

www.porter-cable.com

for a catalog or for the name of your nearest

supplier.

WARNING:

Since accessories other than those offered by 

Porter-Cable

Delta have not been tested with this product, use of such accessories 

could be hazardous. For safest operation, only 

Porter-Cable 

Delta 

recommended accessories should be used with this product.

901452 - 03-28-02.qxd  5/15/02  9:07 AM  Page 13

Содержание TIGERCLAW 740
















Отзывы: