background image

4- ENG

D25803

RISK TO FLUID 

INJECTION

RISK OF INJURY

OR PROPERTY

DAMAGE WHEN

TRANSPORTING

OR STORING

RISK TO

BREATHING

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• Breathing exhaust fumes will cause

serious injury or death!

• Operate pressure washer in a well

ventilated area. Avoid enclosed
areas such as garages, basements,
etc.

• Never operate unit in a location

occupied by humans or animals.

• Some cleaning fluids contain sub-

stances which could cause injury
to skin, eyes, or lungs.

• Use only cleaning fluids specifically

recommended for high pressure
washers. Follow manufacturers
recommendations. Do not use
chlorine bleach or any other
corrosive compound. 

• Fuel or oil can leak or spill and

could result in fire or breathing
hazard, serious injury or death can
result. Fuel or oil leaks will dam-
age carpet, paint or other surfaces
in vehicles or trailers.

• If pressure washer is equipped with

a fuel shut-off valve, turn the valve
to the off position before
transporting to avoid fuel leaks. If
pressure washer is not equipped
with a fuel shut-off valve, drain the
fuel from tank before transporting.
Only transport fuel in an OSHA
approved container. Always place
pressure washer on a protective
mat when transporting to protect
against damage to vehicle from
leaks. Remove pressure washer
from vehicle immediately upon arrival
at your destination.

• Your washer operates at fluid

pressures and velocities high
enough to penetrate human and
animal flesh, which could result in
amputation or other serious injury.
Leaks caused by loose fittings or
worn or damaged hoses can result
in injection injuries. DO NOT
TREAT FLUID INJECTION AS A
SIMPLE CUT! See a physician
immediately!

• Never place hands in front of nozzle.
• Direct spray away from self and

others.

• Make sure hose and fittings are

tightened and in good condition.
Never hold onto the hose or fittings
during operation.

• Do not allow hose to contact muf-

fler.

• Never attach or remove wand or

hose fittings while system is pres-
surized.

• Injuries can result if system

pressure is not reduced before
attempting maintenance or
disassembly.

• To relieve system pressure, shut off

engine, turn off water supply, and
pull gun trigger until water stops
flowing.

• Use only hose and high pressure

accessories rated for pressure
higher than your pressure washer's
p.s.i.

• Do not use acids, gasoline, kero-

sene, or any other flammable
materials in this product. Use only
household detergents, cleaners and
degreasers recommended for use
in pressure washers.

• Wear protective clothing to protect

eyes and skin from contact with
sprayed materials.

• Use of acids, toxic or corrosive

chemicals, poisons, insecticides, or
any kind of flammable solvent with
this product could result in serious
injury or death.

RISK OF 

CHEMICAL

BURN

Содержание D25803-025-1





















Отзывы: