VANITY INSTALLATION - VANITY KIT 89890-00
Unpack L’Expression Vanity
carefully, taking care that bottom of unit does not drop and cause damage to the door panel and side gables (see
FIGURE 2.1).
Unpack L’Expression Minimalist Table carefully, taking care that the unit and glass top does not drop (see FIGURE 2.2).
NOTE: Remove and discard the reinforcement stringer that holds the top and bottom metal bar during shipping. The stringer is
not required.
Provide suitable reinforcement in the wall for anchoring the vanity to the wall. Centerline of reinforcement should be 30-5/8" up from the floor
(see FIGURE 3.0 / 3.2
).
Rough in supply lines and waste per rough-in dimensions (see FIGURE 1.0).
Decorative molding may need to be notched to seat the vanity flush against the wall.
Move the assembled Minimalist Table into place and level with the adjustable levellers on the bottom of the legs. The levellers can be adjusted
outward up to 3/4” but it is recommended not to exceed 1/2” if possible.
Mark the 2 holes located in each of the (1) Top and Bottom Metal Bar located at the back of the Minimalist Table onto the wall. Drill and insert 4
plastic anchoring hardware provided into the wall. Anchor the Minimalist Table securely to the wall through the (1) Metal Bar
(see Figure 3.1 / 3.2)
using 4 screws provided
. Tighten the screws and snap the dome covers provided onto the screws. The dome covers conceal the screws.
Position the (2) L’Expression Vanity by nesting the notch at the back of the Vanity over the lower (1) Metal Bar (see FIGURE 3.1 / 3.2).
Mark the 2 holes located in each of the Top and Bottom Rear Stringer of Vanity onto the wall. Drill and insert 4 plastic anchoring hardware provided
into the wall. Anchor the Vanity securely to the wall using 4 screws provided through the Top and Bottom Rear Stringer
(see Figure 3.2
).
Secure the (3) Metal Stand-offs of the Minimalist Glass Top to the leg supports of the Minimalist Table using the 4 screws provided (see FIGURE 3.1).
Continue with installation appropriate for L’Expression Round Lavatory and faucet options chosen (see FIGURE 3.1 .
C/L of 2 x 6
Reinforcement
Finished
Floor
30 5/8"
(778)
27 3/16" to
(691)
FIGURE 3.0
FIGURE 3.1
(1
) METAL FLAT BAR
SECURES TO WALL
METAL BAR FITS INTO
(2
) SECURE VANITY TO
WALL USING 4x SCREWS
NOTCH AT BACK OF
VANITY
NOTCH AT BACK
OF VANITY
L'EXPRESSION
ROUND LAVATORY
10411-00
L'EXPRESSION VANITY
with DOORS
89411-00
L'EXPRESSION
MINIMALIST TABLE
89450-00
(1
) METAL FLAT BAR
SECURES TO WALL
L'EXPRESSION MINIMALIST
GLASS TOP
89470-00
(3)
METAL STAND-OFF's
FIXED TO THE UNDERSIDE OF
THE MINIMALIST GLASS TOP
SECURE TO THE LEG SUPPORT
FIGURE 2.1 | VANITY 89411-00
Units : Inches (mm)
FIGURE 2.2 | MINIMALIST TABLE 89450-00
Units : Inches (mm)
20 3/4
(527)
17 3/16
(437)
17 3/16
(437)
4 3/4
(121)
23 3/8
(594)
10 15/16
(277)
DOOR
10 15/16
(277)
DOOR
15 3/8
(391)
18
(457)
DOOR
NOTCH TO FIT
ONTO METAL SUPPORT
OF THE L'EXPRESSION
MINIMALIST TABLE
P-TRAP CUT-OUT
FOR L'EXPRESSION
ROUND LAVATORY
DOORS WITH
TOUCH LATCH
TO OPEN DOOR
11 11/16
(297)
5 1/2
(140)
FRONT VIEW
SIDE VIEW
FRONT VIEW
SIDE VIEW
35 1/16
(891)
13 5/16
(338)
21 1/4
(540)
35 11/16
(907)
31 13/16
(808)
29 5/8
(752)
1
(25)
1
(25)
3
(76)
CUT-OUT IN GLASS FOR
L'EXPRESSION ROUND LAVATORY
10421-00
L'EXPRESSION MINIMALIST
1/2" (13)
GLASS TOP
2 3/8
(60)
2 3/8
(60)
2 3/8
(60)
13/16
(21)
1 11/16
(43)
TOWEL
BAR
1/2
(13)
7 7 0 0 2 0 - 1 0 0
- 2 -
