Pop ProSet 3400 Скачать руководство пользователя страница 6

Страница: 6 / 20

Page 6

Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Common Nosepieces

* Included with the tool

For T-Rivets use PRN625 nosepiece when using 3/16” (4.8mm) diameter rivets and PRN825 for ¼” (6.4mm)
diameter rivets. For Monobolt

rivets use N-410 nosepiece for 3/16” (4.8mm) and N-414 for ¼” (6.4mm)

diameter rivets.

Basic Tool Operation

Before operating the tool check the following:

Inspect tool for damage or leaking oil –

do not use tool if it is damaged or leaking oil.

Check that correct nosepiece is fitted and tightened to 60 - 65 in-lbs [6.8 – 7.3 N-m] torque.

Check that the Nose Housing Nut (8) is tight – hand tighten only.

Connect tool to air supply – see air supply requirements (page 4).

Fit Mandrel Collector (113) – (MCS tool only).

Open air supply valve by sliding red OS Slider (130) on side of tool (see note below).

Insert rivet into nosepiece.

Position rivet in work piece.

Pull trigger to set rivet.

Release trigger – if equipped, MCS suction will draw spent mandrel into the collector.

Note: The ProSet

3400 has an OS (Open-Shut) Valve for switching the air supply ON and OFF to

save air when the tool is not in use.

Closed End

HR Rivets

Rivet

Diameter

Open End

Steel

Mandrel

Aluminum

Mandrel

Aluminum

Body

Steel
Body

HS Rivets Ultra-Grip

Jaw Pusher

1/8”

(3.2 mm)

PRN414* PRN424

PRN434

PRN414*

PRN4HR

5/32”

(4.0 mm)

PRN514* PRN524

PRN534

PRN514*

PRN5HR

FAN276-064*

3/16”

(4.8 mm)

PRN614* PRN624

PRN634

PRN614*

PRN6HR

N-406

1/4”

(6.4 mm)

PRN811* PRN822

PRN811*

PRN8PS

PRN8PS or

N-407

DPN276-006*

Air Supply ON

: Open OS Valve

by sliding OS Slider in the
direction shown (up).

Air Supply OFF

: Close OS Valve

by sliding OS Slider in the
direction shown (down).

OS Slider

Содержание ProSet 3400





















Результаты поиска

Содержание ProSet 3400

Отзывы:

Pop ProSet 3400, Инструкция по эксплуатации, Страница: 6 / 20

Результаты поиска

Содержание ProSet 3400

Отзывы: