POP UP PUSH 10 PRO Скачать руководство пользователя

Страница: 16 / 20

Page 15

PUSH PRO -0120843

DAILY PREVENTATIVE MAINTENANCE CHECKLIST

PREVENTATIVE MAINTENANCE REPORT

DATE

OWNER

MODEL NO.

SERIAL NO.

SERVICED BY

OPERATOR’S MANUAL

ELECTRICAL SYSTEM

Battery Terminals

Battery Charge Indicator

Battery Charger

Cables and Wiring Harness

HYDRAULIC SYSTEM

Fluid Level

Hoses, tubes and fittings

CASTORS

MANUAL BRAKES

LOWER CONTROL STATION

Operating Controls

Emergency Stop

Lowering Alarm and Interrupt

EMERGENCY LOWERING

SAFETY PROP

STRUCTURES

Weldments - Scissors, chassis,
steps, platform, etc.

Platform Slide Rollers

Fasteners

UPPER CONTROL STATION

Guardrail System

Platform Floor

Entry Gate

Operating Controls

Lowering Delay

Emergency Stop

OPERATION AND SAFETY DECALS

ITEM

INSPECT FOR

Y N R

In manual holder, all pages readable and intact.

Clean, connectors tight.

Proper operation.

No wear or physical damage.

Between full and add marks with platform stowed.

No leaks, all fittings tight.

Good condition, no damage/smooth movement.

Proper operation, no damage or deformation.

Proper operation.

Shuts off lower controls/proper operation.

Sounds when platform lowers/proper operation.

Proper operation.

No damage or deformation.

Welds intact, no damage or deformation.

In place, no damage or deformation.

In place, tight, and no damage.

Welds intact, no damage or deformation.

All fasteners in place, no loose or missing parts.

No damage or deformation.

Clean to prevent slip and fall hazards.

Proper operation, no damage or deformation.

Proper operation/raise and lower.

Proper operation, limit switch delays lowering.

Shuts off upper controls.

In place and readable.

Maintenance Table Key: Y = Yes/Acceptable, N = No/Not Acceptable, R = Repaired/Acceptable

Содержание PUSH 10 PRO





















Результаты поиска

Содержание PUSH 10 PRO

Отзывы:

Похожие инструкции для PUSH 10 PRO

Бренды по названию

Популярные бренды

POP UP PUSH 10 PRO, Руководство по безопасности и обслуживанию оператора

Результаты поиска

Содержание PUSH 10 PRO

Отзывы:

Похожие инструкции для PUSH 10 PRO

Бренды по названию

Популярные бренды