PoolRite innoSphere 630, Руководство пользователя, Страница: 8 / 16

STARTING UP PROCEDURE
Priming The Pump
Priming the pump is required if the installation is
above the pool water level. If the pump is installed
below the water level isolating valves should be fitted
then go to “Starting The Filter”.
1. Remove clear pump lid, then fill pump bowl with
water to the suction inlet level.
2. Check the rubber pump lid seal is clean and
lightly lubricated with silicone-based grease and is
correctly located in the groove.
3. Replace clear lid.
Starting The Filter (New Pools)
1. Set innoValve to WASTE position.
2. Vacuum clean pool to waste to remove excess
debris from pool and pipes (refer to VACUUM
CLEANING section page 9).
(Existing Pools)
3. Set innoValve to BACKWASH position.
4. Ensure all plumbing lines to and from the pool are
clear (i.e. shut off valves are OPEN).
5. Switch the pump ON.
6. Observe reaction through clear pump lid:
The pump will first draw water in surges until all
the air within the pump bowl and suction piping
has been expelled. If air is still present after
approximately 3 minutes repeat “Priming The
Pump” instructions, then if air is still present,
check the following:
a) Pump lid correctly tightened onto seal.
b) “O” Rings fitted under unions.
c) Backnuts tightened fully (by hand only).
d) Plumbing joints (all glued)
e) Sufficient water in pool.
f) Skimmer weir is free and not jammed.
g) Strainer baskets not blocked.
h) All appropriate in-line valves open.
i) If air is still present the suction pipe to the
skimmer should be checked.
7. After pump has fully primed, run for approximately
three (3) minutes or until water in Sight Glass
becomes clear.
8. Switch pump OFF.
9. Turn valve handle to RINSE position.
10. Switch pump ON and run until water in Sight
Glass is again clear (approx. 20 seconds).
11. Switch pump OFF.
12. Turn valve handle to FILTER position.
13. Switch pump ON.
14. The filter system is now filtering the pool and the
pressure gauge should be reading in the green
FILTER range.
15. When the pressure gauge reading reaches the
start of the red CLEAN band, the filter must be
cleaned by BACKWASHING.
7
7
STARTING UP PROCEDURE
Priming The Pump
Priming the pump is required if the
installation is above the pool water
level. If the pump is installed below
the water level isolating valves should
be fitted then go to "Starting
The Filter".
1. Remove clear pump lid, then fill
pump bowl with water to the
suction inlet level.
2. Check the rubber pump lid seal is
clean and lightly lubricated
with silicone-based grease
and is correctly located
in the groove.
3. Replace clear lid.
Starting The Filter
(New Pools)
1. Set SMARTVALVE to
WASTE position.
2. Vacuum clean pool to waste
to remove excess debris from
pool and pipes (refer to VACUUM
CLEANING section page 9).
(Existing Pools)
3. Set SMARTVALVE to BACKWASH
position.
4. Ensure all plumbing lines to and
from the pool are clear (i.e. shut off
valves are OPEN).
5. Switch the pump ON.
6. Observe reaction through clear
pump lid:
The pump will first draw water in
surges until all the air within the pump
bowl and suction piping has been
expelled. If air is still present after
approximately 3 minutes repeat
"Priming The Pump" instructions, then
if air is still present, check the
following:
a) Pump lid correctly tightened onto
seal.
b) "O" Rings fitted under unions.
c) Backnuts tightened fully (by hand
only).
d) Plumbing joints (all
glued)
e) Sufficient water in
pool.
f) Skimmer weir is free
and not jammed.
g) Strainer baskets not
blocked.
h) All appropriate in-line
valves open.
i) If air is still present the suction
pipe to the skimmer should be
checked.
7. After pump has fully primed, run for
approximately three (3) minutes
or until water in SMARTVALVE
Sight Glass becomes clear.
8. Switch pump OFF.
9. Turn valve handle to RINSE
position.
10.Switch pump ON and run until
water in Sight Glass is again clear
(approx. 20 seconds).
11.Switch pump OFF.