PoolRite innoSphere 630 Скачать руководство пользователя страница 4

HOW A HIGH RATE MEDIA 

FILTER WORKS

The filter pump draws water from the pool and forces it under pressure into the multi-function innoValve where 
it is directed into the top of the filter tank via an overdrain diffuser. The water then flows down through the 
media bed, into the underdrain and back to the pool.

The  action  of  the  water  containing  suspended  particles  passing  through  the  filter  bed  causes  the  larger 
particles to be trapped and retained by the Diamond Kleen. Some of the very small particles may, however, pass 
completely through the filter and return to the pool, but in the process will have gained an electrostatic charge 
due to their high velocity over the media. This charge causes these particles to be attracted together to form 
clusters which are then large enough to be trapped by the Diamond Kleen on their next pass through the filter.

This is a normal characteristic of all high rate media filters.

As the quantity of suspended particles trapped in the media bed increases, the passage of water becomes 
progressively  restricted,  but  this  also  results  in  an  improvement  in  filtration  fineness.  However  when  this 
restriction to flow becomes excessive (as indicated by the rise in gauge pressure) the filter must be cleaned to 
restore a normal flow of water.

Cleaning is achieved by reversing the flow of water so it flows upwards through the media bed causing the 
individual grains of filter media to become buoyant and allow the bed to expand and release the trapped dirt 
particles which are then flushed out of the filter to the waste drain. This process is called BACKWASHING.

DELIVERY OF YOUR MEDIA FILTER

Each Poolrite filter/pump is delivered in two cartons as follows:

CARTON 1

 Factory assembly filter includes:
- Lateral
- Tank
- Clamp bands
- Gasket
-  Installation & Owners Manual 

with Warranty Card.

CARTON 2

Factory assembly innoValve includes:
- innoValve Multiport Valve
-  Three 50 x 50mm take-off 

unions with ‘O’ Rings.

- Three 50 x 40mm reducing bushes.

3

Содержание innoSphere 630

















Отзывы: