Polychem PHT401 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 21

Polychem PHT401 Скачать руководство пользователя страница 11

( M4 ) ( M5 ) ( M6 )

( M7 ) ( M8 ) ( M9 )

Remove the pushing spring (pic.M1), disconnect the motor pipe (pic.M2), remove the 6 bottom plate
screws (pic.M3), unscrew the holding screw (pic.M4), remove the nut on connection shaft (pic.M5)
and pull it out from main frame (pic.M6) pay attention to the shim. Remove the feed wheel shaft nut
(pic.M7) Remove the front cover, the bush, the clutch system with the feed wheel (pic.M8); replace
the worn part (pic. M9) Reassemble in reverse order.

Bottom plate grippers replacement

Remove the 6 bottom plate screws (pic.N1), unscrew the grippers screws (pic.N2), replace the parts
(pic.N3), and reassemble.

( N1 ) ( N2 ) ( N3 )

Welding gripper replacement

Remove the cutter as shown in L1 to L5 sequence, remove the bottom plate as point N1, remove the
safety circlip from welding gripper pin (pic.O1), remove the pin from welding gripper (pic.O2), and
replace the worn out part (fig. O3). Reassemble all parts in reverse order.

( O1 ) ( O2 ) ( O3 )

«
...
9
10
11
12
13
...
»

Содержание PHT401






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды