LECOASPIRA 712
68
E
E
N
N
G
G
L
L
I
I
S
S
H
H
Most fabric types, other than delicates can
be STEAM-ironed at this temperature,
please consult the garment label. If you want
to DRY iron, set the knob (
Y
) to the required
temperature for the fabric as, shown on the
dial.
Nb fabric indications on dial are for DRY
ironing, for STEAM ironing set at maxi-
mum travel as explained above.
• Wait for a few minutes until the Iron heating”
indicator light (
X1
) goes out, to show that the
soleplate of the iron has reached the re-
quired temperature.
• Press the steam request button (
X
)
on the
iron to release bursts of steam from the
holes on the soleplate. Release the button
and the steam will stop.
When you first start
to use the iron, a few drops of water may
come out of the sole-plate mixed with the
steam due to imperfect heat stabilisation. It is
therefore advisable to direct the first jet of
steam onto a rag.
• In order to obtain a continuous jet of steam
move the sliding switch (
W1
). The steam will
continue to come out even when the steam
request button (
X
) is released. To stop the
flow of steam push the sliding switch back-
wards (
W1
).
RECOMMENDED TECHNIQUE
for STEAM iro-
ning with Polti iron is APPLY steam (button
X
)
on the upstroke, then release button (
X
) (so no
steam) for the backstroke, so reclosing the fi-
bres, preventing oversteaming and wetness.
DRY IRONING
• FOR DRY IRONING ONLY (NOT steam iro-
ning), press the main switch (
1
) and adjust
the temperature of the iron by turning dial (
Y
)
to the temperature required for the fabric (as
shown on the dial).
NOTE:
using the iron, it is advisable to adjust
the steam jet at a medium range, or to do some
testing in order to find the jet which is more
suitable to the fabric to be ironed.
IMPORTANT NOTE
• Do not leave the iron unattended whilst con-
nected to the mains.
• Iron only on heat resistant surfaces and on
surfaces that allow the steam to escape e.g.
mesh ironing boards.
• In case of accidental fall of the appliance it is
necessary to have it checked by an author-
ized service center as the internal safety fea-
tures may have been affected.
•
ATTENTION: if you iron sitting down, do not
place your legs under the ironing board, the
steam can cause burns.
G
G
E
E
N
N
E
E
R
R
A
A
L
L
M
M
A
A
I
I
N
N
T
T
E
E
N
N
A
A
N
N
C
C
E
E
Before carrying out any type of maintenance
make sure that the power cable has been dis-
connected from the mains.
After using the brushes it is advisable to allow
the bristles to cool in their natural position so as
to avoid them getting deformed in any way.
Check the conditions of the gaskets located in-
side the monobloc plug (
B2
) periodically.
If necessary, replace them with the appropriate
spares. Also carry out the same check on the
gaskets for connecting the extension tubes (
D
)
and the handle (
A2
).
To clean the outside of the appliance, just use a
damp cloth. Do not use solvents or detergents
as these might damage the plastic surface.
To clean the “ECOACTIVE-FILTER” holder and
clean or change the sponge filter, follow the in-
structions in the paragraph headed “EMPTY-
ING AND CLEANING THE DIRT
CONTAINER”.
W
W
A
A
S
S
H
H
A
A
B
B
L
L
E
E
H
H
E
E
P
P
A
A
F
F
I
I
L
L
T
T
E
E
R
R
WARNING:
Vaporetto Lecoaspira is equipped
with a washable filter. To clean the filter, pro-
ceed as follows:
• Unfasten the handle (
22
) of the dirt container
and remove the container (
20
) as described
in the paragraph headed “PREPARING THE
APPLIANCE FOR USE”.
• Lift the Hepa filter release lever (
18
) and re-
move the filter from its recess (Fig. 14).
• Rinse the filter in cold running water. Shake it
gently after washing to eliminate any residual
dirt and excess water.
NOTE:
let the filter dry naturally, far away
from light and heat sources. You should wait
24 hours before reassembling the filter in the
appliance.
• Replace the filter if it is torn.
• The filter should be cleaned every 4 months.
LECOASPIRA 712 - M0S09201 1Q03:Layout 1
23/03/2010
11.37
Pagina 68
Содержание VAPORETTO LECOASPIRA 712
Страница 1: ......
