ture dial to the ••• position and click twice on
the iron button (8). A powerful blast of steam
will allow you to speed up and improve iro-
ning, even on heavy fabrics, and to remove
the most difficult creases.
If you wish to repeatedly activate the steam
jet, we recommend you wait until the iron re-
turns to maximum temperature.
6. VERTICAL IRONING
The iron may be used in the vertical position
to remove creases from fabrics and/or to re-
fresh the fabric fibres, eliminating any resi-
dual odours.
Hold the iron in a vertical position, press the
button (8), and if permissible based on the ty-
pe of fabric, touch it lightly with the plate.
7. DRY IRONING / DELICATE FABRICS
Ensure that section 1 has been followed, adju-
sting the temperature of the iron (6) to the
lowest temperature as in section 2 and iron
without pressing the steam button.
8. OUT OF WATER
If the appliance is out of water, the red out-
of-water indicator light on the appliance will
turn on (10) and no steam will be produced.
To restart operations just fill the water tank
again as described in the section 1.
9. CALC CLEANING SYSTEM
The Polti Vaporella Simply Calc Cleaning sy-
stem enables the removal of limescale, thus
guaranteeing a better supply of steam, avoi-
ding the leakage of stains or dirt from the ho-
les in the plate.
Running the Calc Cleaning cycle regularly gi-
ves better performance and durability over ti-
me. Run the cycle whenever the blue indica-
tor light around the ON/OFF switch (
)
flashes and when the appliance emits a beep.
In any case, it is possible to perform the clea-
ning cycle at any time.
Before running the cleaning cycle, make sure
you have a large receptacle or bowl on hand
to collect the water, steam and limescale that
will come out from the iron during the pro-
cess, thus avoiding the wetting of the ironing
board or surface on which you are ironing.
How to clean limescale using the “Calc Clea-
ning” cycle:
- Fill the tank halfway with water.
- Make sure the machine is on.
- Position the temperature dial on the maxi-
mum value.
- Keep the ON/OFF switch (
) pressed until
the appliance emits a triple beep (for at
least 7 seconds), release the switch;
- Place the iron above the receptacle/bowl
and press the steam activator on the iron to
begin the cleaning cycle;
- During the cleaning cycle, the LED light fla-
shes blue; hot water, steam and limescale
particles will come out from the iron. The
cleaning cycle takes approximately 1 mi-
nute, do not interrupt the flow until it is
complete.
- At the end of the complete cleaning cycle,
the triple beep indicates that the procedure
has finished and the blue indicator light
around the iron will stop flashing.
- After having run the Calc Cleaning proce-
dure, residual water may leak from the
plate.
- Dry the iron with a cloth.
- You may now resume normal ironing.
If for any reason you decide to end the clea-
ning cycle before it finishes, keep the
ON/OFF BUTTON (
) pressed (for at least 7
seconds) until the appliance emits a triple
beep. Cleaning will be interrupted and the
blue LED light will stop flashing.
10. GENERAL MAINTENANCE
Except when running the Calc Cleaning cycle,
always unplug the appliance from the power
mains before conducting any maintenance
upon it, making sure that the product has
cooled down before proceeding.
To clean the outside of the appliance, use
only a damp cloth.
Do not use detergents of any type.
Clean the iron soleplate when it is completely
cold with a damp cloth or with a non-abrasive
sponge.
11. STORAGE
11.1 Turn off the appliance and disconnect
from the mains electricity.
11.2 Wait for the appliance to cool down
completely before storing it.
11.3 Empty the water tank.
11.4 Place the iron onto the mat, securing it
with the special locking button on the front of
the appliance (11). Press the button to unlock
it
(12)
11.5 Place the power cable and water hose in
their special housing (13).
WARNING:
The
iron
is
hot
and
its
temperature depends on the dial position.
E
N
G
L
IS
H
| 24 |
Содержание Vaporella SIMPLY VS10.09
Страница 4: ...4...
