V A P O R E L L A P O W E R S Y S T E M
29
pliance to an appropriate collection facility at
the end of its useful lifespan.
Appropriate separate collection to permit recy-
cling, treatment and environmentally compati-
ble disposal helps prevent negative impact on
the environment and human health and promo-
tes recycling of the materials making up the
product. For more information on available col-
lection facilities, contact your local waste col-
lection service or the shop where you bought
this appliance.
II
II
M
M
M
M
P
P
P
P
O
O
O
O
R
R
R
R
T
T
T
T
A
A
A
A
N
N
N
N
T
T
T
T
Before leaving our factory all our products are
rigorously tested. This is the reason why your
VAPORELLA may contain some residual water
in the boiler.
P
P
P
P
R
R
R
R
E
E
E
E
P
P
P
P
A
A
A
A
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
F
F
F
F
O
O
O
O
R
R
R
R
U
U
U
U
S
S
S
S
E
E
E
E
1a. Rest the board on the floor.
2a. To open the ironing board, just pull the iron-
ing surface upwards keeping a foot on Va-
porella side leg of the board until locking
takes place (fig. A).
To adjust height, unfasten the lever (
O
) and
move the board upwards or downwards.
NOTE:
Because of the weight of the ironing
surface, during closing and height adjust-
ment hold the board with both hands.
3a. Insert the cable holder (
M
) in its location
(fig. 1).
4a. Place the monoflex (iron power supply -
steam tube) (
E
) in its support (fig. 2).
5a. Unscrew the safety cap (
A
) and fill the
boiler with about 1 litre of water using the
filler bottle (
I
)
(fig.3) making sure that it
does not overflow.
Normal tapwater can be used. However, as
hard water by its nature contains limestone,
which may cause a build-up of limescale in
the boiler, in hard water areas we recom-
mend the use of our natural-base decalci-
fier KALSTOP, available from your Polti
dealer or by mail order from your Polti serv-
ice Centre.
WARNING:
Do NOT under any circumstan-
ces put or leave the filler bottle in the water
filling aperture of the appliance when the
appliance is connected to the mains electri-
city supply. Danger of burns!
6a. Connect the power supply cable (
D
) into an
earthed power supply of the correct volt-
age.
7a. Press the main switch (
B
); the steam pres-
sure indicator (
K
) and the “iron heating” in-
dicator light (
J1
) light up (fig. 4).
8a. To operate the board, turn the board main
switch (
C
) on. In this way the board heater
starts working.
Wait a few minutes to allow the heater to
reach working temperature.
It is now possible to activate blowing and
suction features:
9a.
BLOWING:
By pushing the function switch
(
P
) on position (
I
), the board allows you to
swell the clothes with a “hot blow”, so that
you can gently skim with the iron the most
delicate clothes, ironing them with steam
only.
10a.
SUCTION:
By pushing the function switch
(
P
) on position (
II
), the board holds the
clothes to the surface and eliminate the
residual humidity.
Note:
to avoid condensation inside the
ironing board we recommend to use the
suction function while steam ironing.
II
II
N
N
N
N
S
S
S
S
T
T
T
T
R
R
R
R
U
U
U
U
C
C
C
C
T
T
T
T
II
II
O
O
O
O
N
N
N
N
S
S
S
S
F
F
F
F
O
O
O
O
R
R
R
R
U
U
U
U
S
S
S
S
E
E
E
E
Before ironing a garment, it is always advisable
to check the symbols and instructions on the la-
bel provided by the garment manufacturer.
Check which kind of ironing is recommended,
referring to the table below:
Steam ironing allowed
For dry ironing, set the iron tempera-
ture on •••
Steam ironing allowed
For dry ironing, set the iron tempera-
ture on ••
Check the fabric's resistance to
steam ironing, dry iron allowed with
temperature set on •
- do not iron
- steam ironing or treatment not al-
lowed
EE
EE
NN
NN
GG
GG
LL
LL
II
II
SS
SS
HH
HH
vl power system m0s06959 1l12.qxp 18/01/2006 15.37 Pagina 29
Содержание VAPORELLA POWER SYSTEM
Страница 1: ...Crema E 2H P Pro P Power System...
