To activate this function, just press the TUR-
BO button on the appliance (9). The Turbo
function has a maximum duration of 10 minu-
tes. To reactivate it just press the TURBO
switch again.
9. 360° FLUID CURVE TECHNOLOGY
PLATE
The innovative multidirectional rounded sole-
plate with a scratch-resistant covering allows
for 360° ironing. The pointed tip reaches the
most difficult areas and the concentration of
steam in this area smooths even the most
stubborn creases. The channels distribute the
steam evenly, making the iron slide more ea-
sily for faster ironing with less effort.
10. AUTOMATIC SWITCH-OFF
After 10 minutes without use (calculated from
the last operation carried out on the
appliance), the boiler and the iron switch off
automatically. The indicator light
flashes.
To re-activate the appliance, press the switch
.
11. OUT OF WATER
A lack of water in the tank is identified by the
out-of-water light coming on (
) (10).
To restart operations just fill the water tank
again as described in section 1.
12. GENERAL MAINTENANCE
Before carrying out any maintenance on the
device, always unplug it from the power
mains making sure that the product has
cooled down before proceeding.
To clean the outside of the appliance, use
only use a damp cloth.
Do not use detergents of any type.
For good maintenance of the boiler we
suggest using Polti Kalstop, the special anti-
limescale product, distributed by Polti, and
available for sale at all major domestic-
appliance stores or online at www.polti.com.
Clean the iron soleplate when it is completely
cold with a damp cloth or with a non-abrasive
sponge.
13. CALC CLEANING
OF THE BOILER
(special maintenance)
This special function makes it possible to ex-
tend the life of Polti Vaporella Next and auto-
matically indicates when the boiler needs to
be cleaned.
When the Calc Cleaning light comes on (
)
(11) proceed as follows:
13.1 Disconnect the appliance and let it cool
down for at least 2 hours, if it is hot.
13.2 Empty the water from the tank to pre-
vent leaking.
13.3 Place the appliance onto its side to un-
screw the boiler cap (12).
13.4 Pour 250 ml of cold water into the boiler.
13.5 Rinse out the boiler and pour the water
away into the sink or into a container for
collecting dirty water. If the water is very
dirty, repeat the operation until it is clean.
13.6 Put 100 ml of water into the boiler and
screw back the cap. Make sure that the seal is
in and the cap is screwed on properly.
13.7 Refill the water tank.
13.8 Reconnect the plug to the mains electri-
city (3).
13.9 Press the switch
.
13.10 Press the Turbo switch and the ON/OFF
switch
together for at least five seconds.
The Calc Cleaning light (
) will turn off.
13.11 Now the appliance can be used normally
again.
Do not use this mode for ironing synthetic,
silk and wool clothing.
WARNING: Steam.
Risk of scalding!
WARNING:
Risk
of
scalding!
When
accessing the boiler (removing the cap,
filling
up,
emptying),
ensure
that
the
appliance is switched off at the power
switch and has been disconnected from the
mains for at least two hours.
The maintenance light coming on does not
affect normal use of the appliance. It is pos-
sible to continue ironing. However, cleaning
the boiler when the light comes on will keep
your Polti Vaporella Next in perfect opera-
ting condition for longer.
WARNING: Do not exceed the quantity of
water recommended and pour it slowly into
the boiler, paying attention not to let it
overflow.
E
N
G
L
IS
H
| 25 |
Содержание VAPORELLA NEXT VN18.10
Страница 4: ...4...
Страница 66: ...DEUTSCH 66...
